Oracle X7-8 Скачать руководство пользователя страница 35

Страница: 35 / 308

System Module (SMOD) Overview

■

Oracle ILOM

■

Dual Oracle ILOM image

■

Signed Oracle ILOM image

■

512 MB DDR4 memory

■

128 MB of flash memory

■

1 GB of NAND memory

■

Baseboard management controller (BMC)

■

One RJ-45 serial management port (SER MGT).

■

One network management port, 1 Gbps (NET MGT).

■

One USB 3.0 port external on each SMOD.

■

Four 10GBase-T ports per SMOD (NET0-3).

■

Four hot swap capable disk drive bays. Four SAS3 storage drive bays 0-7.

■

Four drives in each SMOD. SMOD0 0-3 and SMOD1 0-3. Drives can be a total of eight

2.5-inch, hot-swappable SAS3 hard disk drives (HDDs) or eight 2.5-inch SAS3 solid state

drives (SSDs).

Two SMODs are accessible from the back panel of the server. The following illustration shows

SMODs and removal and installation levers with green lock release tabs.

About the Oracle Server X7-8

Содержание X7-8





















































































































































































































































































































Результаты поиска

Содержание X7-8

Отзывы:

Бренды по названию

Популярные бренды

Oracle X7-8, Руководство по обслуживанию

Результаты поиска

Содержание X7-8

Отзывы:

Бренды по названию

Популярные бренды