Oracle X7-8 Скачать руководство пользователя страница 143

Страница: 143 / 308

Remove a Power Supply

Call

Out

Status LED or Button

Icon and

Color

Description

■ Steady On – PS is connected to a properly rated

AC power source.

Ejector lever

None

Used to release the power supply from the chassis

Note -

To access the FIM release latch, remove the top power supply (PS3).

To unlock the power supply lever, squeeze together the two green release

latches at the end of the lever (1).

This action is accompanied by a click sound.

To disengage the power supply from its internal connector, rotate the lever to the

left (2).

Caution -

Pinch point. When operating the lever, keep your fingers clear of the hinged end of

the lever.

The pawl at the hinged end of the lever engages the sidewall of the server and provides the

pivot point for leverage to disengage the power supply. This action leaves the power supply

extending partially from its slot.

Servicing Components

143

Содержание X7-8





















































































































































































































































































































Результаты поиска

Содержание X7-8

Отзывы:

Бренды по названию

Популярные бренды

Oracle X7-8, Руководство по обслуживанию

Результаты поиска

Содержание X7-8

Отзывы:

Бренды по названию

Популярные бренды