Oracle X7-8 Скачать руководство пользователя страница 53

Страница: 53 / 308

Clear Hardware Fault Messages (Oracle ILOM)

Note -

After servicing the component, you might need to clear the fault in Oracle ILOM. Refer

the service procedure for the component for more information.

Clear Hardware Fault Messages (Oracle ILOM)

After servicing the following components, you must clear the fault event in Oracle ILOM:

■

Processor (CPU)

■

PCIe card

■

HBA

■

Front Indicator Module (FIM)

This procedure uses the Oracle ILOM CLI interface. Use the Oracle ILOM CLI to access the

Fault Management Shell,

fmadm

For more information about how to use the Oracle ILOM Fault Management Shell and

supported commands, see the

Oracle ILOM User's Guide for System Monitoring and

Diagnostics Firmware: Release 4.0.x

in the Oracle Integrated Lights Out Manager (ILOM) 4.0

Documentation Library at

http://www.oracle.com/goto/ilom/docs

Caution -

The purpose of the Oracle ILOM Fault Management Shell is to help Oracle Service

personnel diagnose system problems. Customers should not launch this shell or run fault

management commands in the shell unless requested to do so by Oracle Service personnel.

Open an SSH session and at the command line log in to the SP Oracle ILOM CLI.

ssh root@

ipaddress

where

ipaddress

is the IP address of the server SP.

For more information, see

“Using Oracle ILOM” in

Oracle Server X7-8 Installation Guide

The Oracle ILOM CLI prompt appears:

To access

fmadm

, type:

start /SP/faultmgmt/shell

The

fmadm

prompt appears:

Troubleshooting and Diagnostics

Содержание X7-8





















































































































































































































































































































Результаты поиска

Содержание X7-8

Отзывы:

Бренды по названию

Популярные бренды

Oracle X7-8, Руководство по обслуживанию

Результаты поиска

Содержание X7-8

Отзывы:

Бренды по названию

Популярные бренды