Oracle X7-8 Скачать руководство пользователя страница 267

Страница: 267 / 308

Exit BIOS Setup Utility

Exit BIOS Setup Utility

Use the left and right arrow keys to navigate to the top-level Save & Exit Menu.

Use the up and down arrow keys to select the desired action.

Press Enter to select the option.

In the confirmation screen, select

Yes

to proceed and exit the BIOS Setup Utility,

or select

to stop the exit process.

Note -

After modifying any BIOS settings, the subsequent reboot might take longer than a

typical reboot where no settings were modified. The additional delay is required to ensure that

changes to the BIOS settings are synchronized with Oracle ILOM.

Related Information

■

“Accessing the BIOS Setup Utility” on page 239

■

“BIOS Setup Utility Menu Options” on page 269

Setting Up BIOS Configuration Parameters

267

Содержание X7-8





















































































































































































































































































































Результаты поиска

Содержание X7-8

Отзывы:

Бренды по названию

Популярные бренды

Oracle X7-8, Руководство по обслуживанию

Результаты поиска

Содержание X7-8

Отзывы:

Бренды по названию

Популярные бренды