Oracle X7-8 Скачать руководство пользователя страница 288

Страница: 288 / 308

BIOS IO Menu Selections

Setup Options

Options

Defaults

Description

is available only if the system

supports 64-bit decoding.

Maximum Payload

Auto/128 Bytes/256 Bytes/512

Bytes/1024 Bytes/2048

Bytes/4096 Bytes

Auto

Set the Maximum Payload of the

PCI Express device or allow the

System BIOS to select the value.

Maximum Read Request

Auto/128 Bytes/256 Bytes/512

Bytes/1024 Bytes/2048

Bytes/4096 Bytes

Auto

Set the Maximum Read Request

of the PCI Express device or

allow the System BIOS to select

the value.

PCIe Hot-Plug Support

Disabled/Enabled

Enabled

If enabled, allows the OS to

support PCIe Hot-Plug. If

disabled, it does not allow the

OS to support PCIe Hot-Plug.

BIOS IO Menu IO Virtualization Options

The following table describes the BIOS IO Menu IO virtualization options.

Setup Options

Options

Defaults

Description

VT-d

Disabled/Enabled

Enabled

Enable or disable Intel

Virtualization Technology for

directed I/O (VT-d) by reporting

the I/O device assignment to

VMM through DMA remapping

reporting (DMAR) Advance

Configuration Power Interface

(ACPI) tables.

ACS

Disabled/Enabled

Disabled

If disabled, programs ACS

only to Chipset PCIe Root Port

Bridges. If enabled, programs

ACS to all PCIe Root Port

Bridges.

SR-IOV Support

Disabled/Enabled

Enabled

Single Root I/O Virtualization

(SR-IOV) is used to configure

devices into multiple virtual

devices that can be used on

virtual OS installations. If

supported by the hardware

and set to enabled, all devices

within the system that are SR-

IOV capable are configured

to support SR-IOV and I/O

resources are allocated to the

device as normal. If set to

disabled, I/O resources are not

allocated to the device.

288

Oracle Server X7-8 Service Manual • October 2017

Содержание X7-8





















































































































































































































































































































Результаты поиска

Содержание X7-8

Отзывы:

Бренды по названию

Популярные бренды

Oracle X7-8, Руководство по обслуживанию

Результаты поиска

Содержание X7-8

Отзывы:

Бренды по названию

Популярные бренды