Oracle X7-8 Скачать руководство пользователя страница 142

Страница: 142 / 308

Remove a Power Supply

■

Back Power Supply Fault-Service Required LED located on the server front panel FIM

Call

Out

Status LED or Button

Icon and

Color

Description

Fault-Service Required

Locate LED

Amber

White

Indicates the location of the power supply in the

server:

■ Off – Power supply is operating normally,
■ Fast blink – Use Oracle ILOM to activate this

LED to enable you to locate a power supply

quickly and easily.

Lights steady on when the power supply is in a fault

state.

Power Supply OK LED (green)

Green

Indicates the functional state of the power supply:

■ Off – PS is disconnected
■ Steady On – PS is powered on and functionaing

normally. When this LED is lit, the AC OK LED

is also lit.

Note -

Oracle ILOM signals a fault on any installed

power supply that is not connected to an AC power

source, since it might indicate a loss of redundancy.

AC OK LED (green)

~AC

Green

Indicates the operational state of the power supply:

■ Off – PS is not connected to an AC power

source.

142

Oracle Server X7-8 Service Manual • October 2017

Содержание X7-8





















































































































































































































































































































Результаты поиска

Содержание X7-8

Отзывы:

Бренды по названию

Популярные бренды

Oracle X7-8, Руководство по обслуживанию

Результаты поиска

Содержание X7-8

Отзывы:

Бренды по названию

Популярные бренды