Oracle X7-8 Скачать руководство пользователя страница 71

Страница: 71 / 308

Troubleshooting Using Status Indicators

Call

Out

Status LED

Icon and

Color

Description

Amber

■ Off – Server is operating normally.
■ Steady On – A fault is present in chassis SMOD0 System A.

DPCC Locate LED

■ Off – DPCC is operating normally,
■ Fast blink – Use Oracle ILOM to activate this LED to enable you to locate a DPCC

quickly and easily.

DPCC OK indicator

Green

Indicates the operational state of DPCC:

■ Off – DPCC power is not present.
■ Flashing – DPCC is booting.
■ Steady On – DPCC power is on and running.

AC Power Block Inlet Indicators

Each power inlet on the AC power block at the server back panel has a single green OK

indicator that turns on steady only when the power at the connector is sufficient for the power

supply unit. In the following figure, callout 1 shows the OK indicator for inlet AC 0.

The server back panel AC inlets have the following designations.

Call

Out

Status LED or Button

Icon and

Color

Description

AC 0

~AC

AC 0 (SMOD1) System B

AC 1

~AC

AC 1 (SMOD1) System B

Troubleshooting and Diagnostics

Содержание X7-8





















































































































































































































































































































Результаты поиска

Содержание X7-8

Отзывы:

Бренды по названию

Популярные бренды

Oracle X7-8, Руководство по обслуживанию

Результаты поиска

Содержание X7-8

Отзывы:

Бренды по названию

Популярные бренды