Oracle X7-8 Скачать руководство пользователя страница 145

Страница: 145 / 308

Install a Power Supply

Ensure that the AC power cord for the power supply slot is connected and

secured.

The power cord connects at the back of the server.

Open the power supply lever. Squeeze together the two green release latches at

the end of the lever and rotate the lever to the left.

Access this component directly from the front of the server. Ensure that the power supply lever

is in its fully open position.

Align the power supply with its slot.

Ensure that the connector end of the PS is at the opening of the slot and that the open hinge on

the front of the PS is at the bottom and to the left.

Slide the power supply into the slot until it stops.

To install the power supply, rotate the lever to the right (1).

The pawl at the hinged end of the lever engages the sidewall of the server and provides the

pivot point for the leverage necessary to draw the power supply into the slot and engage the

internal connector. The two green release latches at the end of the lever engage to secure the

power supply in place (2).

Servicing Components

145

Содержание X7-8





















































































































































































































































































































Результаты поиска

Содержание X7-8

Отзывы:

Бренды по названию

Популярные бренды

Oracle X7-8, Руководство по обслуживанию

Результаты поиска

Содержание X7-8

Отзывы:

Бренды по названию

Популярные бренды