Oracle X7-8 Скачать руководство пользователя страница 80

Страница: 80 / 308

Troubleshooting Using Status Indicators

Insertion Blink

The insertion blink is three successive blinks of a hot-swap component's primary status

indicator (for example, the green OK indicator). The insertion blink occurs immediately after

three successive unison blinks (see

“Slow Unison Blink Rate” on page 79

) of all the

component indicators.

Unison Steady On

For the unison steady on, all indicators are simultaneously steady on (see

“Steady

On” on page 77

. This occurs during the front panel lamp test (see

“Front Panel Lamp

Test” on page 76

). This is the only time that the Locate Button/LED indicator is on steady.

Alternating (Invalid FRU) Blink Rate

The alternating (invalid FRU) blink rate is a repeating sequence of lit green and amber

indicators at 1 Hz. This indicates that a component has an incorrect version or mismatch (for

example, a power supply with a lower rating than the one specified). The blink rate is also used

for an unsupported component, or a component in an unsupported slot.

Oracle Server X7-8 Service Manual • October 2017

Содержание X7-8





















































































































































































































































































































Результаты поиска

Содержание X7-8

Отзывы:

Бренды по названию

Популярные бренды

Oracle X7-8, Руководство по обслуживанию

Результаты поиска

Содержание X7-8

Отзывы:

Бренды по названию

Популярные бренды