Oracle X7-8 Скачать руководство пользователя страница 206

Страница: 206 / 308

Replace the Energy Storage Module

Servicing the Energy Storage Module and Cables

This topic provides instructions for servicing the Energy Storage Module (ESM) and extension

cable. The ESM provides emergency power for the SAS drives.

Replace the Energy Storage Module

The Energy Storage Module (ESM) sits in a bracket on the top of the SMOD, between the two

disk enclosures.

Prepare the server for cold service.

This is a cold-service component. Power down the system and disconnect the AC power cables

from the server before performing this procedure.
See

“Preparing the Server for Component Replacement” on page 101

Remove the SMOD. See

“Remove an SMOD” on page 195

Turn the SMOD upside down on a flat surface with the back side facing toward

you.

The ESM is located between the two disk drive enclosures.

206

Oracle Server X7-8 Service Manual • October 2017

Содержание X7-8





















































































































































































































































































































Результаты поиска

Содержание X7-8

Отзывы:

Бренды по названию

Популярные бренды

Oracle X7-8, Руководство по обслуживанию

Результаты поиска

Содержание X7-8

Отзывы:

Бренды по названию

Популярные бренды