manualshive.com logo in svg

Oracle X7-8, Руководство по обслуживанию

Поделиться
Скачать
Oracle X7-8 Скачать руководство пользователя страница 180

Install a Processor

The socket bolster plate has alignment pins that go into holes on the processor-heatsink

module to help center the module during installation.

e.   

Ensure that the processor-heatsink module lies evenly on the bolster plate

and that the captive screws align with the threaded socket posts [1].

f.   

Using a 12 in-lbs/ft (inch-pounds/foot) torque driver with a Torx T30 bit,

tighten the processor-heatsink module to the socket. First, fully tighten

captive nuts 1 and 2. Then fully tighten nuts 3 and 4 [2].

As you tighten nuts 3 and 4, some resistance occurs as the bolster leaf spring rises and

comes in contact with the heatsink.

180

Oracle Server X7-8 Service Manual • October 2017

Содержание X7-8





















































































































































































































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды