manualshive.com logo in svg

Oracle X7-8, Руководство по обслуживанию

Поделиться
Скачать
Oracle X7-8 Скачать руководство пользователя страница 39

System Module (SMOD) Overview

■

One internal USB 3.0 port, located on the bottom of the SMOD
Each SMOD has one unused internal USB 3.0 port that is designated as P0. The port is

located on the underside of the SMOD motherboard next to the PCIe card riser slot.

For component serviceability, locations, and designations, see 

“Identifying

Components” on page 24

.

For replacement procedures, see 

“Servicing System Module (SMOD) Components

(FRU)” on page 195

.

Server Storage Drives

The following illustration shows the eight storage drive externally-accessible back panel bay

locations, which are arranged in two rows of four per SMOD.

Call

Out

Description

1

SMOD0 System A storage drive 0 (HDD/SSD)

2

SMOD0 System A storage drive 1 (HDD/SSD)

3

SMOD0 System A storage drive 2 (HDD/SSD)

About the Oracle Server X7-8

39

Содержание X7-8





















































































































































































































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды