Oracle X7-8 Скачать руководство пользователя страница 240

Страница: 240 / 308

Accessing the BIOS Setup Utility

This section provides the following information:

■

“BIOS Setup Utility Menus” on page 240

■

“BIOS Key Mappings” on page 240

■

“Access BIOS Setup Utility Menus” on page 241

■

“Navigate BIOS Setup Utility Menus” on page 242

BIOS Setup Utility Menus

The following table provides descriptions for the top-level BIOS Setup Utility menus.

Menu

Description

Main

General product information, including memory, time/date, security settings, system serial

number, and CPU and DIMM information.

Advanced

Configuration information for the CPU, trusted computing, USB, and other information. Set the

IP address for the server SP.

Manage configuration settings for I/O devices, such as I/O virtualization settings, and enable and

disable Option ROMs.

Boot

Configure the boot device priority.

Save & Exit

Save changes and exit, discard changes and exit, discard changes, or restore the default BIOS

settings.

See

“BIOS Setup Utility Menu Options” on page 269

for examples of each of these screens.

Related Information

■

“Navigate BIOS Setup Utility Menus” on page 242

BIOS Key Mappings

When viewing the BIOS output from a terminal using the serial console redirection feature,

some terminals do not support function keys. BIOS supports the mapping of function keys

to Control key sequences when serial redirection is enabled. The following table provides a

description of the function key to Control key sequence mappings.

240

Oracle Server X7-8 Service Manual • October 2017

Содержание X7-8





















































































































































































































































































































Результаты поиска

Содержание X7-8

Отзывы:

Бренды по названию

Популярные бренды

Oracle X7-8, Руководство по обслуживанию

Результаты поиска

Содержание X7-8

Отзывы:

Бренды по названию

Популярные бренды