Oracle X7-8 Скачать руководство пользователя страница 241

Страница: 241 / 308

Access BIOS Setup Utility Menus

Function Key

Control Key Sequence

BIOS Setup Function

Ctrl+E

Activate the Setup Utility Help menu.

Ctrl+P

Activate the BIOS Boot Menu.

F10

Ctrl+S

Save and Exit changes.

F12

Ctrl+N

Activate Network boot.

Related Information

■

“Access BIOS Setup Utility Menus” on page 241

■

“Navigate BIOS Setup Utility Menus” on page 242

Access BIOS Setup Utility Menus

You can access the BIOS Setup Utility screens from the following interfaces:

■

Use a terminal (or terminal emulator connected to a computer) through the serial port on the

back panel of the server.

■

Connect to the server using the Oracle ILOM Remote System Console Plus application.

Reset or power on the server.

For example, to reset the server:

■

From the local server

, press the On/Standby button on the front panel of the server to

power off the server, and then press the On/Standby button again to power on the server.

■

From the Oracle ILOM web interface

, click Host Management → Power Control and

select Reset from the Select Action list. Click Save, and then click OK.

■

From the Oracle ILOM CLI

, type

reset /System

After the server resets, to enter the BIOS Setup Utility, press the F2 key (Ctrl

+E from a serial connection) when prompted and while the BIOS is running the

power-on self-tests (POST).

Setting Up BIOS Configuration Parameters

241

Содержание X7-8





















































































































































































































































































































Результаты поиска

Содержание X7-8

Отзывы:

Бренды по названию

Популярные бренды

Oracle X7-8, Руководство по обслуживанию

Результаты поиска

Содержание X7-8

Отзывы:

Бренды по названию

Популярные бренды