Oracle X7-8 Скачать руководство пользователя страница 235

Страница: 235 / 308

Replace the Midplane Assembly

15.

Position the side access cover at the access opening, ensuring that the four

captive screws are aligned with the holes in the side of the chassis.

16.

To secure the access cover to the chassis, tighten the four captive screws.

17.

Install the black plastic insert over the top of the midplane assembly.

Ensure that the orientation of the insert is correct. The insert is fitted to the opening using tabs

and flaps.

18.

Align the top access cover with the opening in the top of the chassis.

19.

To secure the cover to the chassis, tighten the 19 captive screws.

20.

Install the chassis in the rack.

21.

Replace components at the front of the server:

Install the CMODs. See

“Install a CMOD” on page 167

Your server might have four CMODs, or it might have eight.

Install both fan frames. See

“Install a Fan Frame” on page 137

Servicing Components

235

Содержание X7-8





















































































































































































































































































































Результаты поиска

Содержание X7-8

Отзывы:

Бренды по названию

Популярные бренды

Oracle X7-8, Руководство по обслуживанию

Результаты поиска

Содержание X7-8

Отзывы:

Бренды по названию

Популярные бренды