Oracle X7-8 Скачать руководство пользователя страница 200

Страница: 200 / 308

Remove the HBA Card

Servicing the Host Bus Adapter (HBA) Card

This section contains procedures for servicing the HBA card (Oracle Storage 12 Gb SAS PCIe

RAID Host Bus Adapter, Internal 16-Port) that is located inside the system module (SMOD):

■

“Remove the HBA Card” on page 200

■

“Install the HBA Card” on page 203

For component serviceability, locations, and designations, see

“Identifying

Components” on page 24

Remove the HBA Card

This is an internal component that is accessible from the back of the server by removing the

SMOD. The host bus adapter (HBA) card is installed in an internal PCIe slot mounted on the

SMOD motherboard. Perform this procedure to replace the HBA card.

Prepare the server for cold service.

This is a cold-service component. Power down the system and disconnect the AC power cables

from the server before performing this procedure.
See

“Preparing the Server for Component Replacement” on page 101

Remove the SMOD. See

“Remove an SMOD” on page 195

Set the SMOD on a flat surface with the front side facing toward you.

Close the SMOD handles.

Rotate the SMOD 180 degrees so the back (connector) side is facing toward you.

Turn the SMOD upside down and locate the HBA.

Note -

The connector (back) side of the SMOD should still be facing you.

The HBA is located inside the SMOD and is accessible through the an upward-facing opening

on the right side.

200

Oracle Server X7-8 Service Manual • October 2017

Содержание X7-8





















































































































































































































































































































Результаты поиска

Содержание X7-8

Отзывы:

Бренды по названию

Популярные бренды

Oracle X7-8, Руководство по обслуживанию

Результаты поиска

Содержание X7-8

Отзывы:

Бренды по названию

Популярные бренды