manualshive.com logo in svg

Oracle X7-8, Руководство по обслуживанию

Поделиться
Скачать
Oracle X7-8 Скачать руководство пользователя страница 195

Servicing System Module (SMOD) Components (FRU)

Servicing System Module (SMOD) Components (FRU)

This section contains removal and installation procedures for the SMOD:

■

“SMOD Population Rules” on page 195

■

“Remove an SMOD” on page 195

■

“Install an SMOD” on page 197

■

“Servicing the Host Bus Adapter (HBA) Card” on page 200

■

“Servicing the Energy Storage Module and Cables” on page 206

■

“Servicing the Internal USB Flash Drives” on page 213

■

“Replace the System Battery” on page 216

Caution - 

SMODs should be removed and replaced only by authorized Oracle Service

personnel.

See 

“System Module (SMOD) Overview” on page 34

.

SMOD Population Rules

The Oracle Server X7-8 supports two installed SMODs. Both SMOD0 System A and SMOD1

System B are accessable from the back panel.

See 

“System Module (SMOD) Overview” on page 34

.

Remove an SMOD

Perform this procedure to access internal SMOD components, such as the HBA card, the

internal USB ports, the ESM, and the system battery.

Before You Begin

Note - 

Internal USB ports are not used.

■

For component serviceability, locations, and designations, see 

“Identifying

Components” on page 24

.

■

Obtain labels and a pen for labeling cables.

1.

Prepare the server for cold service.

Servicing Components

195

Содержание X7-8





















































































































































































































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды