Oracle X7-8 Скачать руководство пользователя страница 278

Страница: 278 / 308

BIOS Advanced Menu Selections

Setup Options

Options

Defaults

Description

PCI Address (R/O)

Bus device function identifier.

Example format: Bus:Device:

Function

Link Status (R/O)

Connected

Specifies the link status of the

network port.

MAC Address (R/O)

Lists the MAC address of the

network interface controller

(NIC).

Virtual MAC Address (R/O)

Lists the Virtual MAC address

of the network interface

controller (NIC).

BIOS Advanced Menu Driver Health Options

The following table describes the BIOS Advanced Menu driver health options.

Note -

Depending on the devices that are populating your PCIe slots, you will see different

entries if the devices are publishing their driver health status.

Setup Options

Options

Defaults

Description

Intel PRO/1000 PCI-E

(R/O)

Healthy

Lists the health status of drivers/

controllers.

Apache Pass Driver

(R/O)

Healthy

Lists the health status of drivers/

controllers.

Intel 40GbE

Healthy

Lists the health status of drivers/

controllers.

Controller Child 0 (R/O)

Healthy

Intel Ethernet Connection for

X722 for 10GBASE-T

Healthy

AVAGO EFI SAS Driver

(R/O)

Healthy

Lists the health status of drivers/

controllers.

BIOS Advanced Menu Serial Port Console

Redirection Options

The following table describes the BIOS Advanced Menu serial port console redirection options.

278

Oracle Server X7-8 Service Manual • October 2017

Содержание X7-8





















































































































































































































































































































Результаты поиска

Содержание X7-8

Отзывы:

Бренды по названию

Популярные бренды

Oracle X7-8, Руководство по обслуживанию

Результаты поиска

Содержание X7-8

Отзывы:

Бренды по названию

Популярные бренды