Oracle X7-8 Скачать руководство пользователя страница 238

Страница: 238 / 308

Power On the Server

When AC power is applied to the server power inlets, the server boots into standby

power mode. For information, see

“Server Boot Process and Normal Operating State

Indicators” on page 73

Verify that none of the server Service Action Required indicators on externally

facing indicator panels are lit.

Note -

After replacing some components, you must clear the fault in Oracle ILOM to clear fault

indicators. For details, see

“Clear Hardware Fault Messages (Oracle ILOM)” on page 53

Power on the server.

Next Steps

■

“Power On the Server” on page 238

Power On the Server

When AC power is applied to the server power inlets, the server boots into standby

power mode. For information, see

“Server Boot Process and Normal Operating State

Indicators” on page 73

Use the following procedure to reapply main power for all server components.

Ensure that the server is in standby power mode.

To power on the server, do one of the following:

■

From the front of the server, press and immediately release the Power

button on the server front panel.

■

From the Oracle ILOM web interface Summary (home) screen, click

Power

State Turn On

button.

■

From the Oracle ILOM command-line interface (CLI), type:

start /System

Note -

When the server powers on, the power-on self-test (POST) can take several minutes to

complete.

238

Oracle Server X7-8 Service Manual • October 2017

Содержание X7-8





















































































































































































































































































































Результаты поиска

Содержание X7-8

Отзывы:

Бренды по названию

Популярные бренды

Oracle X7-8, Руководство по обслуживанию

Результаты поиска

Содержание X7-8

Отзывы:

Бренды по названию

Популярные бренды