Oracle X7-8 Скачать руководство пользователя страница 122

Страница: 122 / 308

Control the Locate Button/LED Locally

Note -

This procedure is performed locally and requires physical access to the server front

panel.

To control the Locate Button/LED indicator locally, do one of the following:

■

To turn off the blinking Locate Button/LED indicator, press the Locate

Button/LED button.

■

To turn on the Locator indicator, press the Locate Button/LED button.

Note -

Some Oracle ILOM security procedures require that you turn on the Locate Button/LED

indicator locally, as part of a physical presence verification step.

■

To perform a lamp test of all front panel indicators, press the Locate Button/

LED three times within a five-second period.

All of the front panel indicators light up and remain lit for 15-20 seconds.

Component Filler Panels and Non-Powered

Components

A filler panel is a metal or plastic enclosure that does not contain any functioning system

hardware or cable connectors. Filler panels occupy vacant component slots to help control

noise, EMI, and airflow. They are installed at the factory and must remain in the server until

you replace them with a component. If you remove a filler panel and continue to operate your

system with an empty slot, the server might overheat due to improper airflow. Additionally,

some components are installed but are not powered (for example, DPCCs and fan modules). As

with filler panels, these components must remain installed in a fully powered-on server.

122

Oracle Server X7-8 Service Manual • October 2017

Содержание X7-8





















































































































































































































































































































Результаты поиска

Содержание X7-8

Отзывы:

Бренды по названию

Популярные бренды

Oracle X7-8, Руководство по обслуживанию

Результаты поиска

Содержание X7-8

Отзывы:

Бренды по названию

Популярные бренды