manualshive.com logo in svg

Oracle X7-8, Руководство по обслуживанию

Поделиться
Скачать
Oracle X7-8 Скачать руководство пользователя страница 269

BIOS Setup Utility Menu Options

This section includes screens of the main menus in the BIOS Setup Utility for Oracle Server

X7-8. Following the screen for each menu is a table of the options available from that menu.

■

“BIOS Main Menu Selections” on page 269

■

“BIOS Advanced Menu Selections” on page 274

■

“BIOS IO Menu Selections” on page 286

■

“BIOS Boot Menu Selections” on page 290

■

“BIOS Save and Exit Menu Selections” on page 292

Related Information

■

Oracle X7 Series Servers Administration Guide

 at: 

http://www.oracle.com/goto/

x86admindiag/docs

■

“Setting Up BIOS Configuration Parameters” on page 239

BIOS Main Menu Selections

This section includes a screen of the BIOS Main Menu. The options that are available from the

Main Menu are described in the table that follows. Options in the table that are marked as “(R/

O)” are read-only information and cannot be changed.

BIOS Setup Utility Menu Options

269

Содержание X7-8





















































































































































































































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды