manualshive.com logo in svg

Oracle X7-8, Руководство по обслуживанию

Поделиться
Скачать
Oracle X7-8 Скачать руководство пользователя страница 155

Install a PCIe Card

6.

To remove the card, pull it straight up and out of its connector.

Related Information

■

“Install a PCIe Card” on page 155

■

“Returning the Server to Operation” on page 237

Install a PCIe Card

To access a PCIe card, you must first remove its DPCC (see 

“Remove a

DPCC” on page 151

). One or two PCIe cards can be installed in each Dual PCIe Card

Carrier (DPCC).

Perform this procedure when replacing a PCIe card or when changing its configuration.

1.

Prepare the server for service. Choose one of the following methods:

■

Prepare the server for hot service.

■

Prepare the server for cold service.

See 

“Preparing the Server for Component Replacement” on page 101

.

2.

Identify the DPCC PCIe slot.

Servicing Components

155

Содержание X7-8





















































































































































































































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды