Oracle X7-8 Скачать руководство пользователя страница 277

Страница: 277 / 308

BIOS Advanced Menu Selections

Setup Options

Options

Defaults

Description

select the attempt, then press

plus or minus (+/-) keys to move

the attempt up/down in the

attempt order list.

BIOS Advanced Menu Gigabit Network

Connection Options

The following table describes the BIOS Advanced Menu Gigabit network connection options.

Setup Options

Options

Defaults

Description

NIC configuration

Use to configure the network

interface controller.

Link Speed

Auto Negotiated

10 Mbs Half

10 Mbs Full

100 Mbs Half

100 Mbs Full

Specifies the port speed used for

the selected boot protocol.

Wake on LAN

Disable/Enabled

Use this option to enable or

disable wake on LAN.

Blink LEDs

0/1/2/3

Use to identify the physical

network port by blinking the

associated LED.

UEFI Driver (R/O)

Identifies the UEFI driver.

Adapter PBA (R/O)

Product board adapter (PBA)

number. You can use the Intel

Network Adapter PBA number

to search for the adapter's model

number. The PBA number is

a nine digit number that is the

last part of the adapter board

serial number. The PBA number

is presented in this format:

xxxxxxx-xxx

, for example,

C80222-001.

Device Name (R/O)

Device name.

Chip Type (R/O)

Manufacturer and model

number.

PCI Device ID (R/O)

1533

Device identifier.

BIOS Setup Utility Menu Options

277

Содержание X7-8





















































































































































































































































































































Результаты поиска

Содержание X7-8

Отзывы:

Бренды по названию

Популярные бренды

Oracle X7-8, Руководство по обслуживанию

Результаты поиска

Содержание X7-8

Отзывы:

Бренды по названию

Популярные бренды