Oracle X7-8 Скачать руководство пользователя страница 107

Страница: 107 / 308

Prepare the Server for Warm Service (Oracle ILOM Web Interface)

See

“Servicing Components” on page 123

Prepare the Server for Warm Service (Oracle ILOM

Web Interface)

This procedure describes how to prepare the server for warm service. Use warm service to

remove and replace CMOD, DIMM, and processor components without accessing the server

back panel to disconnect AC power cords or shutting down Oracle ILOM.

When Oracle ILOM detects that two fan modules in a single cooling zone (a vertical column)

have been removed, the SP removes power from the CMODs, allowing you to service CMODs

and their subcomponents without removing the power cords. Oracle ILOM remains available in

warm service mode.

For more information about component serviceability, see

“Component Serviceability

Requirements” on page 26

Caution -

Loss of service or component damage. Do not replace any components except for

CMODs and internal CMOD subcomponents while the server is in warm service mode.

Caution -

Data Loss. Do not remove more than one fan module from a column while the system

is in Main power mode. This action removes power from the CMODs and causes an immediate

shutdown. On an eight-CMOD system, this applies to all fan modules. On a four-CMOD

system, this applies to the fan modules in the left-hand fan frame.

Note -

This procedure is performed locally and requires physical access to the server front

panel.

Direct a web browser to Oracle ILOM using the IP address of the server SP and log in as root

or a as user with administrator privileges. See

“Accessing Oracle ILOM” in

Oracle Server X7-8

Installation Guide

The Summary Information page appears.

In the Actions section of the Summary Information page, verify that the Power

State is ON.

If the Power State status shows off, the server is already powered off.

Preparing for Service

107

Содержание X7-8





















































































































































































































































































































Результаты поиска

Содержание X7-8

Отзывы:

Бренды по названию

Популярные бренды

Oracle X7-8, Руководство по обслуживанию

Результаты поиска

Содержание X7-8

Отзывы:

Бренды по названию

Популярные бренды