Oracle X7-8 Скачать руководство пользователя страница 283

Страница: 283 / 308

BIOS Advanced Menu Selections

Setup Options

Options

Defaults

Description

Hyper-threading ALL

Disabled/Enabled

Enabled

Use to enable Hyper Threading.

When enabled, two threads

are available per enabled core.

When disabled, only one thread

per enabled core is available.

Active Processor Cores

A minimum of one up to the

maximum number of cores

available in the processor

package.

All

The number of cores to enable in

each processor package.

SNC

Disable/Enable/Auto

Disable

Enable, disable, or set SNC to

auto.

Hardware Prefetcher

Disabled/Enabled

Enabled

Enable the mid-level cache

(MLC) streamer prefetcher

(MSR 1A4h bit [0]).

Adjacent Cache Prefetcher

Disabled/Enabled

Enabled

Enable the mid-level cache

(MLC) streamer prefetcher

(MSR 1A4h bit [1]).

DCU Streamer Prefetcher

Disabled/Enabled

Enabled

Enable DCU streamer

prefetcher, which is a L1 data

cache prefetcher (MSR 1A4h

[2]).

DCP IP Prefetcher

Disabled/Enabled

Enabled

Enable DCU IP prefetcher,

which is a L1 data cache

prefetcher (MSR 1A4h [3]).

Intel Virtualization Technology

Disabled/Enabled

Enabled

When enabled, a Virtual

Machine Manager (VMM) can

utilize the additional hardware

capabilities provided by Intel

Virtualization Technology.

Stale AtoS

Disabled/Enabled/Auto

Disabled

Enable or disable stale A to S

Dir optimization.

LLC dead line alloc

Disabled/Enabled/Auto

Enabled

Enable to opportunistically fill

dead lines in LLC.

XPT Prefetch

Disable/Enable

Enable

Enable or disable XPT Prefetch.

BIOS Advanced Menu Memory Configuration

Options

The following table describes the BIOS Advanced Menu memory configuration option.

BIOS Setup Utility Menu Options

283

Содержание X7-8





















































































































































































































































































































Результаты поиска

Содержание X7-8

Отзывы:

Бренды по названию

Популярные бренды

Oracle X7-8, Руководство по обслуживанию

Результаты поиска

Содержание X7-8

Отзывы:

Бренды по названию

Популярные бренды