Oracle X7-8 Скачать руководство пользователя страница 284

Страница: 284 / 308

BIOS Advanced Menu Selections

Setup Option

Options

Defaults

Description

Numa

Enabled/Disabled

Enabled

Enable or disable Non Uniform

Memory Access (NUMA).

MMIO High Granularity Size

1G/4G/16G/64G/256G/1024G

64G

Selects the allocation size used

to assign memory-mapped I/

O (MMIO) resources. Total

MMIO space can be up to 32x

granularity.

BIOS Advanced Menu CPU Power Management

Configuration Options

The following table describes the BIOS Advanced Menu CPU power management

configuration options.

Setup Options

Options

Defaults

Description

Power Technology

Disabled/Energy Efficient/

Custom

Enables the power management

features.

EIST (GV3)

Enabled/Disabled

Enabled

Enable or disable Enhanced Intel

SpeedStep Technology (EIST).

Turbo Mode

Enabled/Disabled

Enabled

Enabled mode is supported only

if Turbo Mode is supported in

the CPU. Enabled mode also

requires that Enhanced Multi

Threaded Thermal Monitoring

(EMTTM) be enabled on the

CPU.

CPU C3 report

Enabled/Disabled

Disabled

Enable/disable the CPU

C3 (ACPI C3) report to the

operating system.

CPU C6 report

Enabled/Disabled

Enabled

Enable/disable the CPU

C6 (ACPI C3) report to the

operating system.

Package C State limit

Enabled/Disabled

Enabled

Enable/disable Package C State

limit.

Energy Performance

Performance

Balanced Performance

Balanced Energy

Energy Efficiency

Balanced Performance

Use this option to select the

Energy Performance mode.

Uncore Frequency Scaling

Enabled/Disabled

Disabled

Enable/disable Uncore

Frequency Scaling (USF).

284

Oracle Server X7-8 Service Manual • October 2017

Содержание X7-8





















































































































































































































































































































Результаты поиска

Содержание X7-8

Отзывы:

Бренды по названию

Популярные бренды

Oracle X7-8, Руководство по обслуживанию

Результаты поиска

Содержание X7-8

Отзывы:

Бренды по названию

Популярные бренды