NORDAC PRO (SK 500P) – Manual with installation instructions
250
BU 0600 en-3221
M
Mains choke .................................................. 35
Mains voltage Monitoring (P538) ................. 171
Maintenance ................................................ 244
Marking .......................................................... 21
Mass Inertia PMSM (P246) ......................... 116
Master - Slave ............................................. 156
Master function ............................................ 156
Max. freq. aux setpoint (P411) .................... 134
Maximum frequency (P105) .......................... 99
Mechanical Power (P727) ........................... 191
Menu group ................................................... 78
Messages .................................................... 201
microSD card ................................................. 55
Min. chopper threshold (P554) .................... 179
Min. freq. a-in 1/2 (P410) ............................. 133
Minimal configuration ..................................... 73
Minimum frequency (P104) ........................... 99
Minimum process control frequency (P466) 149
Modulation depth (P218) ............................. 111
Module status(P746) ................................... 198
Module version (P745) ................................ 198
Monitoring
Motor temperature ..................................... 74
Motor cable .................................................... 37
Motor choke ................................................... 37
Motor circuit (P207) ..................................... 108
Motor data ............................ 67, 106, 205, 213
Motor list (P200) .......................................... 106
Motor phase sequence (P583) .................... 182
Motor temperature monitoring ....................... 74
Multi I/O ......................................................... 59
N
Name plate .................................................... 67
No-load current (P209) ................................ 109
Nom. Val process ctrl (P412)....................... 134
Nominal current (P203) ............................... 107
Nominal frequency (P201) ........................... 107
Nominal power (P205) ................................. 108
Nominal speed (P202) ................................. 107
Nominal voltage (P204) ............................... 107
NORD
System bus .............................................. 238
NORDCON computer ................................. 239
Norm. BusIO Out Bits (P482) ..................... 154
Norm. BusIO Out Bits (P483) ..................... 155
O
OK key .......................................................... 61
Op.-time last error (P799) ........................... 200
Operating display .......................................... 59
Operating state ........................................... 201
Operating time (P714)................................. 188
Option monitoring (P120) ............................ 105
Oscillation damping (P217) ......................... 111
Output choke ................................................. 37
Overtemperature ......................................... 205
Overvoltage ................................................. 208
Overvoltage switch-off .................................. 32
P
P - torque limit factor (P111) ....................... 104
P chopper limit (P555) ................................ 180
P set last error (P706) ................................. 185
Par.-identification (P220) ............................ 114
Parameter identification .............................. 114
Parameter lost ............................................. 208
Parameter set (P100).................................... 98
Parameter, Saving mode (P560) ................ 181
Password (P004) .......................................... 84
Peak current PMSM (P244) ........................ 116
Phase U current (P732) .............................. 191
Phase V current (P733) .............................. 192
Phase W current (P734) ............................. 192
PI- process controller .................................. 226
PID control D comp. (P415) ........................ 135
PID control I comp. (P414) ......................... 134
PID control P comp. (P413) ........................ 134
PLC display value (P360) ........................... 126
PLC functionality (P350) ............................. 124
PLC Integer setpoint (P355) ....................... 125
PLC Long setpoint (P356) .......................... 125
PLC set values (P553) ................................ 179
PLC setpoint selection (P351) .................... 125
Содержание SK 510P
