manualshive.com logo in svg

NEC IMAGE P100E - SERVICE, Руководство по обслуживанию

Сервисный мануал NEC IMAGE P100E - это исчерпывающий руководство по обслуживанию данного устройства. Вы можете скачать его бесплатно с manualshive.com и получить всю необходимую информацию по техническому обслуживанию продукта. Не забудьте загрузить свой экземпляр мануала прямо сейчас!

Поделиться
Скачать
background image

2-32     Setup and Operation

EISA Configuration Utility

The ECU program comes on a diskette that ships with the computer and is required for
EISA configuration. The ECU provides a detailed view of the system configuration and
allows you to make system configuration changes when you add, move, or remove an
EISA or ISA expansion board.

Use the ECU program when you are setting up the system for the first time and whenever
you add an EISA, ISA, PCI, or Plug and Play ISA board to fully configure the system. This
ensures that the information in the system's complementary metal oxide semiconductor
(CMOS ) is consistent with the configuration information stored in the BIOS.

The ECU

When you add a board to your configuration and run the ECU program, the utility reads
the board’s corresponding configuration (CFG) file. The ECU uses the CFG file, which
describes the characteristics and the required system resources of the board, to create a
conflict-free configuration.

Once you complete the configuration process, configuration information is saved to the
system’s nonvolatile memory for use any time you power-on the system.

The ECU includes the following features:

n

 

Supports EISA and ISA boards, PCI devices, and Plug and Play boards.

n

 

Automatically detects EISA boards, PCI devices, and Plug and Play ISA boards
installed in your computer.

n

 

Helps you configure ISA boards by providing the approprate switch and jumper
settings.

n

 

Creates and maintains the System Configuration Information (SCI) file as a
backup for the computer’s nonvolatile memory.

n

 

Supports configuration (CFG) file extensions.

n

 

Lets you set the computer’s date and time.

The ECU program comes on the EISA Configuration Utility diskette that ships with your
system.

 

NOTE:  

Do 

not

 execute the EISA Configuration

Utility from your hard disk. The utility program
must start with a 

cold boot

 from the EISA Con-

figuration Utility diskette.

Содержание IMAGE P100E - SERVICE





























































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для IMAGE P100E - SERVICE

IBM Aptiva 2140 Maintenance Service Manual preview
Aptiva 2140
Бренд: IBM Страницы: 212
IBM 9228 - IntelliStation Z - Pro Installation Manual preview
9228 - IntelliStation Z - Pro
Бренд: IBM Страницы: 72
IBM 9114-275 - IntelliStation POWER 275 Installation Manual preview
9114-275 - IntelliStation POWER 275
Бренд: IBM Страницы: 102
IBM 8863 - eServer xSeries 366 Installation Manual preview
8863 - eServer xSeries 366
Бренд: IBM Страницы: 94
IBM 8543 Hints And Tips preview
8543
Бренд: IBM Страницы: 4
IBM 4190 User Manual preview
4190
Бренд: IBM Страницы: 84
IBM 2283 User Manual preview
2283
Бренд: IBM Страницы: 96
IBM 5280 User'S Setup Procedures preview
5280
Бренд: IBM Страницы: 156
IBM 5280 Technical Newsletter preview
5280
Бренд: IBM Страницы: 178
IBM 5280 Maintenance Information Manual preview
5280
Бренд: IBM Страницы: 155
IBM Aptiva 2159 Hardware Maintenance Service preview
Aptiva 2159
Бренд: IBM Страницы: 214
IBM NetVista Quick Reference Manual preview
NetVista
Бренд: IBM Страницы: 68
IBM NetVista A30 Handboek Voor De Gebruiker preview
NetVista A30
Бренд: IBM Страницы: 54
AURES K750 V1.3.indb User Manual preview
K750 V1.3.indb
Бренд: AURES Страницы: 63
Digital Equipment STARION 200i Service Maintenance Manual preview
STARION 200i
Бренд: Digital Equipment Страницы: 96
UUGear Witty Pi User Manual preview
Witty Pi
Бренд: UUGear Страницы: 25
Oracle MICROS Compact Workstation 310 Quick Assembly Manual preview
MICROS Compact Workstation 310
Бренд: Oracle Страницы: 2
Vivo DESK-V000EB Instruction Manual preview
DESK-V000EB
Бренд: Vivo Страницы: 3

Бренды по названию

Популярные бренды

Загрузить еще бренды