Mitsubishi Electric NZ2GF2B-60TCRT4, Руководство пользователя

Страница: 162 / 388

160
(2) Remote buffer memory areas related to auto tuning
To execute auto tuning, the following data need to be set in advance. Note that other data must be preset to the
values used for actual operation since actual control starts on completion of auto tuning.
When "0" is set for the proportional band (P)/heating proportional band (Ph), auto tuning is not executed.
(

Page 318, Appendix 3 (7))
(3) Storing the calculated value after auto tuning
After auto tuning is completed, the calculated values are stored into the following remote buffer memory areas.
*1 A value twice greater than the one in CH  Integral time (I) setting (address: 103H, 133H, 163H, 193H) is automatically
set. However, if this setting is 0 (s) when auto tuning is in process, the loop disconnection detection judgment time is not
stored.
Remote buffer memory area name
Remote buffer memory address
Reference
CH1 CH2 CH3 CH4
CH  Input range 100H 130H 160H 190H Page 312, Appendix 3 (5)
CH  Set value (SV) setting 101H 131H 161H 191H Page 317, Appendix 3 (6)
CH  Upper limit output limiter 105H 135H 165H 195H
Page 321, Appendix 3 (10)
CH  Lower limit output limiter 106H 136H 166H 196H
CH  Heating upper limit output limiter 105H 135H 165H 195H
CH  Cooling upper limit output limiter 1C5H 1CAH 1CFH 1D4H
CH  Output variation limiter setting 107H 137H 167H 197H Page 323, Appendix 3 (11)
CH  Sensor correction value setting 280H 281H 282H 283H Page 352, Appendix 3 (51)
CH  Control output cycle setting 10CH 13CH 16CH 19CH
Page 326, Appendix 3 (15) CH  Heating control output cycle setting 10CH 13CH 16CH 19CH
CH  Cooling control output cycle setting 1C6H 1CBH 1D0H 1D5H
CH  Primary delay digital filter setting 10DH 13DH 16DH 19DH Page 328, Appendix 3 (16)
CH  AUTO/MAN mode shift 113H 143H 173H 1A3H Page 332, Appendix 3 (22)
CH  AT bias setting 2A1H 2A3H 2A5H 2A7H Page 355, Appendix 3 (57)
CH  Forward/reverse action setting 115H 145H 175H 1A5H Page 334, Appendix 3 (24)
CH  Auto tuning mode selection 2A0H 2A2H 2A4H 2A6H Page 354, Appendix 3 (56)
Remote buffer memory area name
Remote buffer memory address
Reference
CH1 CH2 CH3 CH4
CH  Proportional band (P) setting 102H 132H 162H 192H
Page 318, Appendix 3 (7) CH  Heating proportional band (Ph) setting 102H 132H 162H 192H
CH  Cooling proportional band (Pc) setting 1C4H 1C9H 1CEH 1D3H
CH  Integral time (I) setting 103H 133H 163H 193H Page 320, Appendix 3 (8)
CH  Derivative time (D) setting 104H 134H 164H 194H Page 320, Appendix 3 (9)
CH  Loop disconnection detection judgment
time
*1
116H 146H 176H 1A6H Page 334, Appendix 3 (25)