Infineon XDPP1100 Скачать руководство пользователя страница 527 | Manualshive

Страница: 527 / 562

Infineon XDPP1100 Скачать руководство пользователя страница 527

User Manual 527 of 562 V 1.0

2021-08-25

XDPP1100 technical reference manual

Digital power controller

Central processing unit subsystem

15.11

I

2

C module

The XDPP1100 includes an Inven

tra™ I

2

C (MI2CV) module.

The Inventr

a™ MI2CV provides an interface between the microprocessor and an I

2

C bus that conforms to the

Philips I

2

C Bus Protocol (April 1995 Update). It can operate in either master or slave mode. It performs

arbitration in master mode to allow it to operate in multi-master systems. In slave mode, it can interrupt the
processor when it recognizes its own 7-bit or 10-bit address or the general call address.

The Cortex®-M0 accesses I

2

C registers through the APB interface at base address 700B_0000h.

The I

2

C block diagram is shown in

Figure 121

I

2

C block diagram

15.11.1

I

2

C operating modes

The I

2

C can operate in four modes: master transmit, master receive, slave transmit, and slave receive. The I

2

C

will automatically enter slave transmit mode if it receives its own slave address and a read bit. It will similarly
enter slave receive mode if it receives either its own slave address and a write bit, or the general call address.

15.11.1.1

Status information

The state of the interface at any time is indicated by the status code recorded in the STAT register.

There are 28 status codes corresponding to the different possible states of the I

2

C, plus a further code that

indicates when no relevant status information is available.

The states reported cover all conditions from successful transmission to bus errors and loss of arbitration.

The appropriate microprocessor responses to the reported interface condition and the I

2

C actions these invoke

are detailed in the I

2

C Product Specification.

5-bit status codes (STAT register) are described in

Clock

Address[2:0]

Wdata[7:0]

VAL

RD

Rdata[7:0]

INTR

NOE

CPU

interface

Clock

divider

Controller

I/O shift

register

Bus activity

detector

Bus I/P

filter

SCL_out

SDA_out

SCL_in

SDA_in

«
...
525
526
527
528
529
...
»

Содержание XDPP1100



















































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды