manualshive.com logo in svg

Freescale Semiconductor PowerQUICC MPC870, Справочное руководство

Продукт Freescale Semiconductor PowerQUICC MPC870 - это мощный полупроводниковый процессор, который обеспечивает высокую производительность и эффективность. Вы можете загрузить "Reference Manual" бесплатно с нашего сайта, чтобы ознакомиться с полной инструкцией по использованию этого продукта.

Поделиться
Скачать
background image

ATM Overview

MPC885 PowerQUICC Family Reference Manual, Rev. 2

Freescale Semiconductor

36-9

 

36.7

Serial ATM Operation

The SCCs running serial ATM operate independently of the physical interface standard used. The TDM 
ports can be used with serial ATM to allow an easy connection to an E1 or T1 line interface device. It is 
also possible to use an SCC directly through the NMSI. 

In addition to the functions provided for UTOPIA operation, the serial ATM mode includes a transmission 
convergence (TC) layer. The TC layer provides cell delineation, scrambling, idle cell generation or 
filtering, and defines the interface characteristics to support E1/T1 or xDSL line interface devices.

36.7.1

Serial ATM Transmit Overview

The serial transmit process begins with the APC. The APC controls the ATM traffic of the transmitter 
through a user-configured timer that defines the maximum outgoing bit rate. The APC uses each ATM 
channel’s specific traffic parameters to divide the total bit rate among the active channels. It can provide 
CBR, VBR and UBR traffic services. ABR can also be supported through software manipulation of APC 
parameters. The task of the APC is to define the next channel (or channels) to be transmitted. Refer to 

Chapter 40, “ATM Pace Control,”

 for additional information about the operation and programming of the 

APC.

When operating in serial mode, transmit requests are internally generated by an SCC. The transmitter takes 
the next channel from the transmit queue for the SCC. It then reads the channel-specific information from 
the transmit connection table (TCT), and updates the TCT. The cell data is then copied from the transmit 
buffer to an internal buffer where the CRC32 and HEC are calculated, the cell header is appended, and 
scrambling is optionally performed. After the cell assembly process, the cell is moved into the SCC’s 
transmit FIFO for transmission.

The transmitter appends the trailer of the CPCS-PDU in the last cell of an AAL5 user frame. The 
CPCS-PDU consists of the frame length (which is calculated during the frame transmit), the CPCS-UU 
and CPI fields from the TxBD, and cell padding as required. The transmitter also sets PTI[1] in the header 
of the last cell of the frame. An interrupt can be optionally generated to declare the end of a transmit frame.

When transmitting AAL0 cells, the ATM controller copies the cell (except the HEC) from the channel’s 
cell transmit buffer. The ATM controller optionally generates CRC10 for the cell payload and places the 
result at the end of the payload. This feature is used to support OAM CRC10 per ITU specification I.610.

The transmitter sends idle cells (with idle cell contents defined by the user) if there are no channel numbers 
in the transmit queue or if the current channel in the transmit queue has no valid buffers. An idle cell will 
continue to be sent each time the APC schedules this channel in the transmit queue until either a buffer is 
made ready or a 

TRANSMIT DEACTIVATE CHANNEL

 command is issued. For additional information about ATM 

controller commands, refer to 

Section 39.4, “Port-to-Port (PTP) Switching.”

 

36.7.2

Serial ATM Receive Overview

The serial receive process starts after the receiver becomes synchronized with the incoming cells and can 
perform cell delineation. A receive request is then generated by an SCC. The receiver copies the first word 
from the SCC to the dual-port RAM (DPR). The receiver translates the header address (VCI/VPI/PTI) to 
a channel number through either a look-up table in dual-port RAM, address compression tables in external 

Содержание PowerQUICC MPC870



















































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для PowerQUICC MPC870

TYAN S3950 Manual preview
S3950
Бренд: TYAN Страницы: 82
Gigabyte GP-WB8260MD Installation Manual preview
GP-WB8260MD
Бренд: Gigabyte Страницы: 8
ON Semiconductor NCN8024GEVB Series User Manual preview
NCN8024GEVB Series
Бренд: ON Semiconductor Страницы: 5
AMPTRON M817 Series User Manual preview
M817 Series
Бренд: AMPTRON Страницы: 41
Intersil ISL70219ASEHEV1Z User Manual preview
ISL70219ASEHEV1Z
Бренд: Intersil Страницы: 10
Advantech SIMB-M02 Startup Manual preview
SIMB-M02
Бренд: Advantech Страницы: 4
IEI Technology WAFER-PV-D4253 User Manual preview
WAFER-PV-D4253
Бренд: IEI Technology Страницы: 140
RAK RAK8213 User Manual preview
RAK8213
Бренд: RAK Страницы: 17
Advantech EmbCore ROM-7421 Quick Start Manual preview
EmbCore ROM-7421
Бренд: Advantech Страницы: 25
MSI K9N6PGM2-V2 - Motherboard - Micro ATX User Manual preview
K9N6PGM2-V2 - Motherboard - Micro ATX
Бренд: MSI Страницы: 153
Analog Devices AD9741 Quick Start Manual preview
AD9741
Бренд: Analog Devices Страницы: 6
Parker ACR8010 Hardware Manual preview
ACR8010
Бренд: Parker Страницы: 56
MSI Baby AT SI19 Owner'S Manual preview
Baby AT SI19
Бренд: MSI Страницы: 104
Linear DC2048A Demo Manual preview
DC2048A
Бренд: Linear Страницы: 16
Biostar TA790GX A3+ Setup Manual preview
TA790GX A3+
Бренд: Biostar Страницы: 67
Texas Instruments TLV320AIC12KEVM-K User Manual preview
TLV320AIC12KEVM-K
Бренд: Texas Instruments Страницы: 40
DFI PR810-C622 User Manual preview
PR810-C622
Бренд: DFI Страницы: 47
DFI LanParty NFII Ultra B User Manual preview
LanParty NFII Ultra B
Бренд: DFI Страницы: 120

Бренды по названию

Популярные бренды

Загрузить еще бренды