manualshive.com logo in svg

Freescale Semiconductor PowerQUICC MPC870, Справочное руководство

Продукт Freescale Semiconductor PowerQUICC MPC870 - это мощный полупроводниковый процессор, который обеспечивает высокую производительность и эффективность. Вы можете загрузить "Reference Manual" бесплатно с нашего сайта, чтобы ознакомиться с полной инструкцией по использованию этого продукта.

Поделиться
Скачать
background image

Serial Communications Controllers

MPC885 PowerQUICC Family Reference Manual, Rev. 2

Freescale Semiconductor

21-11

 

when a high-priority TxBD has been prepared and enough time has passed since the last SCC transmission. 

Table 21-4

 describes TODR fields. This register is affected by HRESET and SRESET.

21.3

SCC Buffer Descriptors (BDs)

Data associated with each SCC is stored in buffers and each buffer is referenced by a buffer descriptor 
(BD) that can reside anywhere in dual-port RAM. The total number of 8-byte BDs is limited only by the 
size of the dual-port RAM (128 BDs/1 Kbyte). These BDs are shared among all serial controllers—SCCs, 
SMCs, SPI, and I

2

C. The user defines how the BDs are allocated among the controllers.

Each 64-bit BD has the following structure:

•

The half word at  0x0 contains status and control bits that control and report on the data 
transfer. These bits vary from protocol to protocol. The CP updates the status bits after the buffer 
is sent or received.

•

The half word at  0x2 (data length) holds the number of bytes sent or received. 

— For an RxBD, this is the number of bytes the controller writes into the buffer. The CP writes 

the length after received data is placed into the associated buffer and the buffer closed. In 
frame-based protocols (but not including SCC transparent operation), this field contains the 
total frame length, including CRC bytes. Also, if a received frame’s length, including CRC, is 
an exact multiple of MRBLR, the last BD holds no actual data but does contain the total frame 
length.

— For a TxBD, this is the number of bytes the controller should send from its buffer. Normally, 

this value should be greater than zero. The CP never modifies this field.

•

The word at  0x4 (buffer pointer) points to the beginning of the buffer in memory (internal 
or external).

— For an RxBD, the value must be even.

— For a TxBD, this pointer can be even or odd. 

Shown in 

Figure 21-6

, the format of Tx and Rx BDs is the same in each SCC mode. Only the status and 

control bits differ for each protocol.

Table 21-4. TODR Field Descriptions

Bits

Name

Description

0

TOD

Transmit on demand.
0 Normal operation
1 The CP gives high priority to the current TxBD and begins sending the frame without waiting the 

normal polling time to check TxBD[R]. TOD is cleared automatically after one serial clock, but 
transmitting on demand continues until an unprepared (R = 0) BD is reached. TOD does not need 
to be set again if new TxBDs are added to the BD table as long as older TxBDs are still being 
processed. New TxBDs are processed in order. The first bit of the frame is typically clocked out 
5-6 bit times after TOD is set. 

1–15

—

Reserved, should be cleared.

Содержание PowerQUICC MPC870



















































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для PowerQUICC MPC870

Intel BOXDH57JG Product Manual preview
BOXDH57JG
Бренд: Intel Страницы: 78
Udoo Bolt Get Started And Safety Instruction Manual preview
Bolt
Бренд: Udoo Страницы: 9
Biostar G41D-M7 Setup Manual preview
G41D-M7
Бренд: Biostar Страницы: 47
IBASE Technology MB997 User Manual preview
MB997
Бренд: IBASE Technology Страницы: 84
Ublox SARA-N3 series User Manual preview
SARA-N3 series
Бренд: Ublox Страницы: 18
Texas Instruments BQ25170 User Manual preview
BQ25170
Бренд: Texas Instruments Страницы: 19
Gigabyte MX33-BS0 User Manual preview
MX33-BS0
Бренд: Gigabyte Страницы: 81
MSI H6M-E22 (G3) User Manual preview
H6M-E22 (G3)
Бренд: MSI Страницы: 171
Global American 3307800 User Manual preview
3307800
Бренд: Global American Страницы: 135
Arbor Technology EmETXe-i91M0 User Manual preview
EmETXe-i91M0
Бренд: Arbor Technology Страницы: 68
Safran STIM300 User Manual preview
STIM300
Бренд: Safran Страницы: 29
DFI E586-ICP User Manual preview
E586-ICP
Бренд: DFI Страницы: 96
Honda BF 30 DK2 SHGU Instructions For Use Manual preview
BF 30 DK2 SHGU
Бренд: Honda Страницы: 132
Analog Devices AD911 Series User Manual preview
AD911 Series
Бренд: Analog Devices Страницы: 12
Advantech PCM-9370F Startup Manual preview
PCM-9370F
Бренд: Advantech Страницы: 4
Supermicro A2SDi-16C-TP8F User Manual preview
A2SDi-16C-TP8F
Бренд: Supermicro Страницы: 109
Supermicro X10SRM-F User Manual preview
X10SRM-F
Бренд: Supermicro Страницы: 126
Shuttle HOT-679V User Manual preview
HOT-679V
Бренд: Shuttle Страницы: 50

Бренды по названию

Популярные бренды

Загрузить еще бренды