manualshive.com logo in svg

Freescale Semiconductor PowerQUICC MPC870, Справочное руководство

Продукт Freescale Semiconductor PowerQUICC MPC870 - это мощный полупроводниковый процессор, который обеспечивает высокую производительность и эффективность. Вы можете загрузить "Reference Manual" бесплатно с нашего сайта, чтобы ознакомиться с полной инструкцией по использованию этого продукта.

Поделиться
Скачать
background image

Serial Communications Controllers

MPC885 PowerQUICC Family Reference Manual, Rev. 2

Freescale Semiconductor

21-5

 

19, 20

TRX, 

TTX

Transparent receiver/transmitter. The receiver, transmitter, or both can use totally transparent 
operation, regardless of GSMR_L[MODE]. For example, to configure the transmitter as a UART and 
the receiver for totally transparent operation, set MODE = 0b0100 (UART), TTX = 0, and TRX = 1.
0 Normal operation
1 The receiver/transmitter uses totally transparent mode, regardless of the protocol chosen in 

GSMR_L[MODE]. 

For full-duplex totally transparent operation, set both TTX and TRX.
Note that an SCC cannot operate half in Ethernet or serial ATM mode and half in transparent mode. 
For example, if MODE = 0b1100 (Ethernet), erratic operation occurs unless TTX = TRX.

21, 22

CDP, 

CTSP

CD/CTS pulse. If the SCC is used in the TSA and is programmed in transparent mode, set CTSP 
and refer to 

Section 28.3.2, “Synchronization and the TSA,” 

for options on programming CDP.

0 Normal operation (envelope mode). CD/CTS should envelope the frame. Negating CD/CTS 

during reception causes a CD/CTS lost error.

1 Pulse mode. Synchronization occurs when CD/CTS is asserted; further CD/CTS transitions do 

not affect reception.

23, 24

CDS, 

CTSS

CD/CTS sampling. Determine synchronization characteristics of CD and CTS. If the SCC is in 
transparent mode and is used in the TSA, CDS and CTSS must be set. Also, CDS and CTSS must 
be set for loopback testing in transparent mode.
0 CD/CTS is assumed to be asynchronous with data. It is internally synchronized by the SCC, then 

data is received (CD) or sent (CTS) after several clock delays.

1 CD/CTS is assumed to be synchronous with data, which speeds up operation. CD or CTS must 

transition while the Rx/Tx clock is low, at which time, the transfer begins. Useful for connecting 
MPC885 in transparent mode since the RTS of one MPC885 can connect directly to the CD/CTS 
of another.

25

TFL

Transmit FIFO length
0 Normal operation. SCC2–SCC4 Tx FIFOs are 16 bytes each. 
1 The Tx FIFO is 1 byte. This option is used with character-oriented protocols, such as UART, to 

ensure a minimum FIFO latency at the expense of performance.

26

RFW

Rx FIFO width
0  Receive FIFO is 32 bits wide for maximum performance; the Rx FIFO is 16 bytes for 

SCC2–SCC4. Data is not normally written to receive buffers until at least 32 bits are received. 
This configuration is required for HDLC-type protocols and Ethernet and is recommended for 
high-performance transparent protocols.

1 Low-latency operation. The receive FIFO is 8 bits wide, reducing the Rx FIFO to a quarter its 

normal size. This allows data to be written to the buffer as soon as a character is received, instead 
of waiting to receive 32 bits. This configuration must be chosen for character-oriented protocols, 
such as UART. It can also be used for low-performance, low-latency, transparent operation. 
However, it must not be used with HDLC, HDLC Bus, AppleTalk, or Ethernet because it causes 
erratic behavior.

27

TXSY

Transmitter synchronized to the receiver. Intended for X.21 applications where the transmitted data 
must begin an exact multiple of 8-bit periods after the received data arrives.
0 No synchronization between receiver and transmitter (default).
1 The transmit bit stream is synchronized to the receiver. Additionally, if RSYN = 1, transmission in 

totally transparent mode does not occur until the receiver synchronizes with the bit stream and 
CTS is asserted to the SCC. Assuming CTS is asserted, transmission begins 8 clocks after the 
receiver starts receiving data.

Table 21-2. GSMR_H Field Descriptions (continued)

Bits

Name

Description

Содержание PowerQUICC MPC870



















































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для PowerQUICC MPC870

Texas Instruments AFE4500EVM User Manual preview
AFE4500EVM
Бренд: Texas Instruments Страницы: 52
ST STM32746G-EVAL User Manual preview
STM32746G-EVAL
Бренд: ST Страницы: 79
Gigabyte 7ZXR Series User Manual preview
7ZXR Series
Бренд: Gigabyte Страницы: 125
Infineon UltraHub User Manual preview
UltraHub
Бренд: Infineon Страницы: 24
natus otometrics HI-PRO 2 Installation Manual preview
otometrics HI-PRO 2
Бренд: natus Страницы: 22
JETWAY 917GBAR3A User Manual preview
917GBAR3A
Бренд: JETWAY Страницы: 54
Freescale Semiconductor KIT34825EPEVME User Manual preview
KIT34825EPEVME
Бренд: Freescale Semiconductor Страницы: 28
Gigabyte 5VMM User Manual preview
5VMM
Бренд: Gigabyte Страницы: 87
QMTECH XILINX SPARTAN-7 User Manual preview
XILINX SPARTAN-7
Бренд: QMTECH Страницы: 15
IEI Technology NANO-QM871-i1 User Manual preview
NANO-QM871-i1
Бренд: IEI Technology Страницы: 156
Intel BOXDP55KG Product Manual preview
BOXDP55KG
Бренд: Intel Страницы: 92
Vector ZCB User Manual preview
ZCB
Бренд: Vector Страницы: 73
Microchip Technology AVR-IoT WA User Manual preview
AVR-IoT WA
Бренд: Microchip Technology Страницы: 35
Texas Instruments AMC7823 EVM User Manual preview
AMC7823 EVM
Бренд: Texas Instruments Страницы: 19
Gigabyte GA-C847N-D User Manual preview
GA-C847N-D
Бренд: Gigabyte Страницы: 44
Gigabyte GA-Z97X-Gaming G1 User Manual preview
GA-Z97X-Gaming G1
Бренд: Gigabyte Страницы: 136
Richtek RT1025 User Manual preview
RT1025
Бренд: Richtek Страницы: 15
Nuvoton NuMaker NUC980 IIoT User Manual preview
NuMaker NUC980 IIoT
Бренд: Nuvoton Страницы: 46

Бренды по названию

Популярные бренды

Загрузить еще бренды