manualshive.com logo in svg

Freescale Semiconductor PowerQUICC MPC870, Справочное руководство

Продукт Freescale Semiconductor PowerQUICC MPC870 - это мощный полупроводниковый процессор, который обеспечивает высокую производительность и эффективность. Вы можете загрузить "Reference Manual" бесплатно с нашего сайта, чтобы ознакомиться с полной инструкцией по использованию этого продукта.

Поделиться
Скачать
background image

Memory Management Unit

MPC885 PowerQUICC Family Reference Manual, Rev. 2

8-8

Freescale Semiconductor

 

— To define four different 1-Kbyte pages, create four level-two descriptors, but set the subpage 

validity flags such that: entry one = 0b1000, entry two = 0b0100, entry three = 0b0010, entry 
four = 0b0001. All other fields of the level-two descriptor can be set differently for each of 
these entries.

— To define two different 2-Kbyte pages, create four level-two descriptors, but set the subpage 

validity flags in pairs such that: entry one = 0b1100, entry two = 0b1100, entry three = 0b0011, 
entry four = 0b0011. The other fields of the ‘paired’ level-two descriptors must be the same for 
each of the pairs.

Other combinations are also possible.

This mode is the most complex and the most inefficient in memory size (that is, MMU tables are 
approximately four times larger). However, it allows the most detailed resolution of protection with 
full functionality.

IMMUs and DMMUs can use different modes; the IMMU could use mode 1 and the DMMU could use 
mode 2, or vice versa. However, if mode 3 is desired, both MMUs must be in mode 3.

8.6

Memory Attributes

Memory attributes defined by the PowerPC architecture are implemented as follows:

•

Reference and change bit updates—The MPC885 does not generate an exception for an R 
(reference) bit update. In fact, there is no entry for an R bit in the TLB. 

The change bit (C) is bit 23 in the level-two descriptor, described in 

Table 8-4

. Software updates C 

(changed) bits, but hardware treats the C bit (negated) as a write-protect attribute. Therefore, 
attempting to write to a page marked unmodified invalidates that entry and causes an 
implementation-specific DTLB error exception. If change bits are not needed, set the C bit to one 
by default in the PTEs.

•

Memory control attributes—The MPC885 supports cache inhibit (CI), writethrough (WT), and 
guarded (G) attributes, defined in the PowerPC Virtual Environment Architecture (VEA). The 
memory coherence (M) attribute is not supported; to ensure memory coherency, configure the page 
as cache-inhibited. 

Chapter 7, “Instruction and Data Caches,”

 describes the effects of CI and WT 

attributes in the MPC885. 

The G attribute is used to map I/O devices that are sensitive to speculative (out-of-order) accesses. 
An attempted speculative access to a page marked guarded (G = 1) stalls until either the access is 
nonspeculative or is canceled by the core. Attempting to fetch from guarded memory causes an 
implementation-specific instruction TLB error interrupt. 

8.7

Translation Table Structure

The MMU hardware supports a two-level software tablewalk. Other table structures are not precluded. 

Figure 8-4

 shows the two-level translation table when MD_CTR[TWAM] = 1 (4-Kbyte resolution of 

protection). 

Содержание PowerQUICC MPC870



















































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для PowerQUICC MPC870

Gigabyte GS-R12PE Service Manual preview
GS-R12PE
Бренд: Gigabyte Страницы: 74
ECS A78F2P-M2 User Manual preview
A78F2P-M2
Бренд: ECS Страницы: 60
ASROCK N68-GS3 FX Quick Installation Manual preview
N68-GS3 FX
Бренд: ASROCK Страницы: 154
Gigabyte Z690M DS3H DDR4 User Manual preview
Z690M DS3H DDR4
Бренд: Gigabyte Страницы: 36
Yamaha 55B Owner'S Manual preview
55B
Бренд: Yamaha Страницы: 223
EVGA X79 SLI Visual Manual preview
X79 SLI
Бренд: EVGA Страницы: 2
IBASE Technology MB991AF User Manual preview
MB991AF
Бренд: IBASE Technology Страницы: 91
Microchip Technology Power Debugger Manual preview
Power Debugger
Бренд: Microchip Technology Страницы: 89
ON Semiconductor NCP1095GEVB User Manual preview
NCP1095GEVB
Бренд: ON Semiconductor Страницы: 5
TYAN S7086 User Manual preview
S7086
Бренд: TYAN Страницы: 130
ON Semiconductor AR0140AT User Manual preview
AR0140AT
Бренд: ON Semiconductor Страницы: 5
ASROCK P4I45PE User Manual preview
P4I45PE
Бренд: ASROCK Страницы: 31
Lenovo EAM-400H User Manual preview
EAM-400H
Бренд: Lenovo Страницы: 51
Abit SM5 User Manual preview
SM5
Бренд: Abit Страницы: 96
Faytech FAY-003 Manual preview
FAY-003
Бренд: Faytech Страницы: 41
ASROCK Z97M Pro4 Manual preview
Z97M Pro4
Бренд: ASROCK Страницы: 152
ASROCK Z97M OC Formula Manual preview
Z97M OC Formula
Бренд: ASROCK Страницы: 168
ASROCK Z97 Pro4 User Manual preview
Z97 Pro4
Бренд: ASROCK Страницы: 113

Бренды по названию

Популярные бренды

Загрузить еще бренды