manualshive.com logo in svg

Freescale Semiconductor PowerQUICC MPC870, Справочное руководство

Продукт Freescale Semiconductor PowerQUICC MPC870 - это мощный полупроводниковый процессор, который обеспечивает высокую производительность и эффективность. Вы можете загрузить "Reference Manual" бесплатно с нашего сайта, чтобы ознакомиться с полной инструкцией по использованию этого продукта.

Поделиться
Скачать
background image

ATM Parameter RAM

MPC885 PowerQUICC Family Reference Manual, Rev. 2

Freescale Semiconductor

38-3

 

0x3A

TSTA

Hword

Time stamp timer address (AAL5 only). Contains the address of the RISC timer 
to be used for the time-stamp process. The receiver copies the RISC timer value 
from the address specified by the TSTA field to the RCT when a new frame is 
received. TSTA should be initialized with a value equal to (T 4*timer 
number). (See the 

Section 18.8, “The RISC Timer Table

.”

)

0x3C

OLDLEN

 1 

Hword

Transmitter temporary length. Do not write to this location.

0x3E

SMRBLR

Hword

SAR maximum receive buffer length register. Determines the number of bytes the 
CP writes to a receive buffer before moving to the next buffer. SMRBLR is 
user-defined and should be a multiple of 48 bytes. SMRBLR is global for all ATM 
connections per controller.

0x40

EHEAD

Word

Empty cell header and empty cell payload for serial mode. Contain the data for 
the empty cell header (EHEAD) and payload (EPAYLOAD). The CP sends and 
receives empty (idle) cells using the data contained in EHEAD and EPAYLOAD. 
When transmitting, the CP assembles an empty cell by sending EHEAD once, 
calculating and sending a HEC, and then sending EPAYLOAD twelve times (48 
bytes). When receiving, the CP compares the incoming header with EHEAD to 
check for empty cells; if they match the cell is discarded.
The user should program EHEAD and EPAYLOAD as required: The ATM Forum 
UNI specification states that unassigned cells should be sent when no valid 
transmit data is available, while the ITU mandates the use of idle cells.
Unassigned cells are used as empty cells when EHEAD = 0x0000_0000 and idle 
cells when EHEAD = 0x0100_0000. In both cases, EPAYLOAD should be 
initialized to 0x6A6A_6A6A. Note that the data for these fields must be written in 
little-endian byte order.

0x44

EPAYLOAD

Word

0x48

TQBASE

Hword

Transmit queue base pointer. Contains the user-defined pointer to the base 
address of the transmit queue in the dual-port RAM. See 

Section 40.7, “PHY 

Transmit Queues.”

In ESAR multi-PHY master mode, this field is reserved. Each PHY has a 
dedicated transmit queue whose pointers reside in the APC priority levels. See 

Section 40.9, “APC Priority Levels.”

0x4A

TQEND

Hword

Transmit queue end pointer. Contains the user-defined pointer to the last entry in 
the transmit queue in the dual-port RAM. The size of the transmit queue is 
user-defined, but note that the minimum number of entries is (NCITS +2). See 

Section 40.7, “PHY Transmit Queues.”

In ESAR multi-PHY master mode, this field is reserved. Each PHY has a 
dedicated transmit queue whose pointers reside in the APC priority levels. See 

Section 40.9, “APC Priority Levels.”

0x4C

TQAPTR

Hword

Transmit queue APC pointer. Points to the next available entry in the transmit 
queue. The APC uses TQAPTR for the channel currently scheduled to transmit. 
TQAPTR automatically wraps back to TQBASE when it reaches the end of the 
queue. See 

Section 40.7, “PHY Transmit Queues.”

Initialize TQAPTR to the value in TQBASE. 
In ESAR multi-PHY master mode, this field is reserved. Each PHY has a 
dedicated transmit queue whose pointers reside in the APC priority levels. See 

Section 40.9, “APC Priority Levels.”

Table 38-1. Serial ATM and UTOPIA Interface Parameter RAM Map (continued)

Offset 

from SCC 

Base

Name

Width

Description

Содержание PowerQUICC MPC870



















































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для PowerQUICC MPC870

IBASE Technology IB100 User Manual preview
IB100
Бренд: IBASE Technology Страницы: 33
Gigabyte 7ZXR Series User Manual preview
7ZXR Series
Бренд: Gigabyte Страницы: 125
Texas Instruments TPS628436-7-8EVM-167 User Manual preview
TPS628436-7-8EVM-167
Бренд: Texas Instruments Страницы: 15
MSI MS-6367 Manual preview
MS-6367
Бренд: MSI Страницы: 30
Gigabyte GA-P55A-UD3P User Manual preview
GA-P55A-UD3P
Бренд: Gigabyte Страницы: 136
Texas Instruments TPA3250D2EVM User Manual preview
TPA3250D2EVM
Бренд: Texas Instruments Страницы: 18
Shuttle FB81 Manual preview
FB81
Бренд: Shuttle Страницы: 81
ASROCK X570 PHANTOM GAMING 4 Manual preview
X570 PHANTOM GAMING 4
Бренд: ASROCK Страницы: 196
Merit Full MAXX Removal And Installation preview
Full MAXX
Бренд: Merit Страницы: 4
Magic-Pro Computer MP-6VIP-C+ User Manual preview
MP-6VIP-C+
Бренд: Magic-Pro Computer Страницы: 40
MATSONIC MS8328E Series User Manual preview
MS8328E Series
Бренд: MATSONIC Страницы: 39
TDK EV MOD CH101-01-02 User Manual preview
EV MOD CH101-01-02
Бренд: TDK Страницы: 10
Atmel PROTO1 Xplained Pro User Manual preview
PROTO1 Xplained Pro
Бренд: Atmel Страницы: 17
Gigabyte GA-H61N-USB3 User Manual preview
GA-H61N-USB3
Бренд: Gigabyte Страницы: 88
Texas Instruments TMP1075EVM User Manual preview
TMP1075EVM
Бренд: Texas Instruments Страницы: 33
Socket MS8158D Series Manual preview
MS8158D Series
Бренд: Socket Страницы: 37
Microchip Technology Voltage Supervisor SOT23 User Manual preview
Voltage Supervisor SOT23
Бренд: Microchip Technology Страницы: 28
Dynatem CPU-71-10 User Manual preview
CPU-71-10
Бренд: Dynatem Страницы: 57

Бренды по названию

Популярные бренды

Загрузить еще бренды