manualshive.com logo in svg

Freescale Semiconductor PowerQUICC MPC870, Справочное руководство

Продукт Freescale Semiconductor PowerQUICC MPC870 - это мощный полупроводниковый процессор, который обеспечивает высокую производительность и эффективность. Вы можете загрузить "Reference Manual" бесплатно с нашего сайта, чтобы ознакомиться с полной инструкцией по использованию этого продукта.

Поделиться
Скачать
background image

SCC Ethernet Mode

MPC885 PowerQUICC Family Reference Manual, Rev. 2

Freescale Semiconductor

27-13

 

of the CRC-encoded result to generate a number between 1 and 64. Bits 31–30 of the CRC result select 
one of the GADDRs or IADDRs; bits 29–26 of the CRC result indicate the bit in that register. 

When the ethernet controller receives a frame, the same process is used. If the CRC generator selects a bit 
that is set in the group/individual hash table, the frame is accepted. Otherwise, it is rejected. So, if eight 
group addresses are stored in the hash table and random group addresses are received, the hash table 
prevents roughly 56/64 (87.5%) of the group address frames from reaching memory. Frames that reach 
memory must be further filtered by the processor to determine if they contain one of the eight preferred 
addresses.

Better performance is achieved by using the group and individual hash tables simultaneously. For instance, 
if eight group and eight physical addresses are stored in their respective hash tables, 87.5% of all frames 
are prevented from reaching memory. The effectiveness of the hash table declines as the number of 
addresses increases. For instance, with 128 addresses stored in a 64-bin hash table, the vast majority of the 
hash table bits are set, thus preventing a small fraction of the frames from reaching memory.

Hash tables cannot be used to reject frames that match a set of entered addresses because unintended 
addresses are mapped to the same bit in the hash table.

27.12 Interpacket Gap Time

The receiver receives back-to-back frames with a minimum interpacket spacing of 9.6 µs. In addition, after 
the backoff algorithm, the transmitter waits for carrier sense to be negated before resending the frame. 
Retransmission begins 9.6 µs after carrier sense is negated if it stays negated for at least 6.4 µs. 

27.13 Handling Collisions

If a collision occurs as a frame is being sent, the ethernet controller continues sending for at least 32 bit 
times, thus sending a JAM pattern of 32 ones. If a collision occurs during the preamble sequence, the JAM 
pattern is sent at the end of the sequence.

If a collision occurs within 64 byte times, the retry process is initiated. The transmitter waits a random 
number of slot times (512 bit times or 52 µs). If a collision occurs after 64 byte times, no retransmission 
is performed and the buffer is closed with an LC error indication. If a collision occurs while a frame is 
being received, reception stops. This error is reported only in the BD if the length of the frame exceeds 
MINFLR or if PSMR[RSH] = 1.

27.14 Internal and External Loopback

Both internal and external loopback are supported by the ethernet controller. In loopback mode, both of 
the SCC FIFOs are used and the channel actually operates in a full-duplex fashion. Both internal and 
external loopback are configured using combinations of PSMR[LPB] and GSMR[DIAG]. Because of the 
full-duplex nature of the loopback operation, the performance of the other SCCs is degraded.

Internal loopback disconnects the SCC from the serial interface. Receive data is connected to the transmit 
data and the receive clock is connected to the transmit clock. Data from the transmit FIFO is received 
immediately into the receive FIFO. There is no heartbeat check in this mode; configure TENA as a 
general-purpose output.

Содержание PowerQUICC MPC870



















































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для PowerQUICC MPC870

AOpen MK77M Online Manual preview
MK77M
Бренд: AOpen Страницы: 95
MSI 845 Ultra Manual preview
845 Ultra
Бренд: MSI Страницы: 96
Foxconn 661FX7MJ Series User Manual preview
661FX7MJ Series
Бренд: Foxconn Страницы: 81
IBASE Technology MI920 User Manual preview
MI920
Бренд: IBASE Technology Страницы: 65
C-Control Duino Mega32 Quick Manual preview
Duino Mega32
Бренд: C-Control Страницы: 8
ON Semiconductor Strata Enabled NCV6357 User Manual preview
Strata Enabled NCV6357
Бренд: ON Semiconductor Страницы: 6
Biostar GF8200 M 2G+ Manual preview
GF8200 M 2G+
Бренд: Biostar Страницы: 37
Avalue Technology EAX-Q170P User Manual preview
EAX-Q170P
Бренд: Avalue Technology Страницы: 79
ASROCK X299 Taichi Manual preview
X299 Taichi
Бренд: ASROCK Страницы: 200
ASROCK 775Twins-HDTV User Manual preview
775Twins-HDTV
Бренд: ASROCK Страницы: 43
Supero X7DAL-E+ User Manual preview
X7DAL-E+
Бренд: Supero Страницы: 89
Freescale Semiconductor M68HC12A4EVB User Manual preview
M68HC12A4EVB
Бренд: Freescale Semiconductor Страницы: 160
Gigabyte GA-H310TN-R2 User Manual preview
GA-H310TN-R2
Бренд: Gigabyte Страницы: 39
Samsung API Ultimate Performance UP1100 Quick Start Installation Manual preview
API Ultimate Performance UP1100
Бренд: Samsung Страницы: 2
Samsung S3F401F Hardware User Manual preview
S3F401F
Бренд: Samsung Страницы: 32
Samsung S3FM02G User Manual preview
S3FM02G
Бренд: Samsung Страницы: 31
Samsung SyncMaster 710V User Manual preview
SyncMaster 710V
Бренд: Samsung Страницы: 40
Samsung s3c6410-TFA Manual preview
s3c6410-TFA
Бренд: Samsung Страницы: 49

Бренды по названию

Популярные бренды

Загрузить еще бренды