manualshive.com logo in svg

Freescale Semiconductor PowerQUICC MPC870, Справочное руководство

Продукт Freescale Semiconductor PowerQUICC MPC870 - это мощный полупроводниковый процессор, который обеспечивает высокую производительность и эффективность. Вы можете загрузить "Reference Manual" бесплатно с нашего сайта, чтобы ознакомиться с полной инструкцией по использованию этого продукта.

Поделиться
Скачать
background image

Serial Interface

MPC885 PowerQUICC Family Reference Manual, Rev. 2

20-32

Freescale Semiconductor

 

In addition to the 144-Kbps ISDN 2B+D channels, the GCI provides two channels for maintenance and 
control:

•

B1 is a 64-Kbps bearer channel

•

B2 is a 64-Kbps bearer channel

•

M is a 64-Kbps monitor channel

•

D is a 16-Kbps signaling channel

•

C/I is a 48-Kbps command/indication channel (includes A and E bits)

The M channel is used to transfer data between layer-1 devices and the control unit (the core) and the C/I 
channel is used to control activation/deactivation procedures or to switch test loops by the control unit. The 
M and C/I channels of the GCI bus should be routed to SMC1 or SMC2, which have modes to support the 
channel protocols. The MPC885 can support any channel of the GCI bus in the primary rate by modifying 
the SI RAM programming.

The GCI supports the CCITT I.460 recommendation as a method for data rate adaptation since it can 
access each bit of the GCI separately. The current-route RAM specifies which bits are supported by the 
interface and serial controller. The receiver accepts only the bits that are enabled by the SI RAM. The 
transmitter sends only the bits that are enabled by the SI RAM and does not drive L1TXDx otherwise. 
L1TXDx is an open-drain output and should be pulled high externally.

The MPC885 supports contention detection on the D channel of the SCIT bus. When the MPC885 has data 
to send on the D channel, it checks an SCIT bus bit that is marked with a special route code (usually, bit 4 
of C/I channel 2). The physical layer device monitors the physical layer bus for activity on the D channel 
and indicates on this bit that the channel is free. If a collision is detected on the D channel, the physical 
layer device drives bit 4 of C/I channel 2 to logic high. The MPC885 then aborts its transmission and 
resends the frame when this bit is driven to logic low again. This procedure is automatically handled for 
the first two buffers of a frame.

20.2.6.1

GCI Activation/Deactivation 

In the deactivated state, the clock pulse is disabled and the data line is at a logic one. The layer-1 device 
activates the MPC885 by enabling the clock pulses and sending an indication on the C/I channel 0. To 
report the arrival of a valid indication in the SMC’s RxBD, the CPM sends a maskable interrupt to the core.

When the core activates the line, the data output of L1TXDx should be programmed to zero by setting 
SIMODE[STZx]. Code 0 (command timing TIM) is sent on C/I channel 0 to the layer-1 device until STZx 
is cleared. The physical layer device resumes the clock pulses and gives an indication on C/I channel 0. 
The core should then clear STZx to enable data output.

20.2.6.2

Programming the GCI Interface

The two GCI interface modes, normal and SCIT, are described in the following sections.

20.2.6.2.1

Normal Mode

For normal mode operation, first program the channels’ SIMODE[DSCx, FEx, CEx, RFSDx] for 
GCI/SCIT mode, defining the sync pulse to GCI sync for framing and the data clock as one-half the input 

Содержание PowerQUICC MPC870



















































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для PowerQUICC MPC870

IEI Technology KINO-AH612 Quick Installation Manual preview
KINO-AH612
Бренд: IEI Technology Страницы: 12
IEI Technology KINO-945GSE User Manual preview
KINO-945GSE
Бренд: IEI Technology Страницы: 190
IEI Technology KINO-9454 Quick Installation Manual preview
KINO-9454
Бренд: IEI Technology Страницы: 8
IEI Technology IMBA-H610 User Manual preview
IMBA-H610
Бренд: IEI Technology Страницы: 193
IEI Technology IMBA-C2360-i2 User Manual preview
IMBA-C2360-i2
Бренд: IEI Technology Страницы: 182
IEI Technology KINO-DBT Series User Manual preview
KINO-DBT Series
Бренд: IEI Technology Страницы: 133
IEI Technology WSB-9454 User Manual preview
WSB-9454
Бренд: IEI Technology Страницы: 234
Texas Instruments INA193EVM User Manual preview
INA193EVM
Бренд: Texas Instruments Страницы: 8
IBM M841LR User Manual preview
M841LR
Бренд: IBM Страницы: 40
Texas Instruments TLV320AIC3111 EVM User Manual preview
TLV320AIC3111 EVM
Бренд: Texas Instruments Страницы: 39
P&E Microcomputer Systems XPC560P EVB User Manual preview
XPC560P EVB
Бренд: P&E Microcomputer Systems Страницы: 53
Nematron AEMQ77-989 User Manual preview
AEMQ77-989
Бренд: Nematron Страницы: 47
Microsemi VSC8584 User Manual preview
VSC8584
Бренд: Microsemi Страницы: 15
Tews Technologies TVME220 Series User Manual preview
TVME220 Series
Бренд: Tews Technologies Страницы: 26
JETWAY NF731 User Manual preview
NF731
Бренд: JETWAY Страницы: 44
IEI Technology Nano-PV-D4251 User Manual preview
Nano-PV-D4251
Бренд: IEI Technology Страницы: 153
Analog Devices AD9361 Reference Manual preview
AD9361
Бренд: Analog Devices Страницы: 128
ASROCK X570 PHANTOM GAMING 4 Manual preview
X570 PHANTOM GAMING 4
Бренд: ASROCK Страницы: 196

Бренды по названию

Популярные бренды

Загрузить еще бренды