Freescale Semiconductor PowerQUICC MPC870 Скачать руководство пользователя страница 1040 | Manualshive

Страница: 1040 / 1426

background image

ATM Controller

MPC885 PowerQUICC Family Reference Manual, Rev. 2

39-18

Freescale Semiconductor

Note that the PTP BD table should be initialized as empty (V bits should be cleared). The transmitter
should be enabled before the receiver. As soon as the receiver is enabled, the receiver and the transmitter
begin independently transferring cells, and the host should not modify the BD table.

39.4.5

APC PTP Queues

Each priority level’s APC PTP queue is implemented using the PTP BD table of the PTP connection
feeding this level. A PTP counter keeps track of the number of valid cells in the queue. (See

Section 40.9,

“APC Priority Levels.”

) The receiver inserts a cell into the APC PTP queue by placing the cell in memory,

setting the current BD[V] in the connection’s PTP BD table and incrementing the PTP counter in the
appropriate APC priority level.

39.5

Statistical Counters

Optional statistical counters can be maintained by the CP to count the number of cells per ATM port (or
per PHY in multi-PHY master mode). This is a useful feature to aid traffic related system debug. When
activated, the free-running counters consume CPM processing power of roughly 5% of the total ATM
utilization. The supported counters are as follows:

•

Total cell count of transmitted cells (TotalTxCells)

•

Total cell count of transmitted cells with the CLP bit set (TotalTxCLP1)

•

Total cell count of received cells (TotalRxCells)

•

Total cell count of received cells with the CLP bit set (TotalRxCLP1)

0x00

(cont.)

2

W

Wrap. Determines that this is the final BD in the table.
0 This is not the last BD in the PTP BD table.
1 This is the last BD in the PTP BD table. After this BD has been used, the CP

returns to using the first BD in the table. The number of BDs in this table is
programmable and is determined only by the W-bit.

3

I

Interrupt. When I is set, a new interrupt queue entry is generated when this buffer
is closed (for both receiving and transmitting).
0 No interrupt is generated.
1 A new interrupt entry with the RXB/TXB bit is added to the interrupt queue after

this buffer has been received/transmitted.

4–31

—

Reserved, should be cleared.

0x04

—

PTP

Buffer

Pointer

PTP (transmit/receive) buffer pointer. Points to the first location of this BD’s data
buffer, which may reside in either internal or external memory. This pointer must be
burst aligned (divisible by 16).

Note:

AAL2 requires 64-byte alignment for AAL0 buffers.

0x08

—

—

Reserved, should be cleared.

0x0A

—

—

Reserved, should be cleared.

Table 39-5. PTP BD Field Descriptions (continued)

Offset from

PTP_BD_PTR

Bits

Name

Description

«
...
1038
1039
1040
1041
1042
...
»

Содержание PowerQUICC MPC870



















































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для PowerQUICC MPC870

Бренд: IBASE Technology Страницы: 33

Бренд: Intel Страницы: 6

NF796M-H310 Series

Бренд: JETWAY Страницы: 63

Бренд: AXIOMTEK Страницы: 2

Бренд: Linear Technology Страницы: 6

Бренд: Supermicro Страницы: 2

Бренд: Biostar Страницы: 47

AP0100CSSL00SPGAH-GEVB

Бренд: ON Semiconductor Страницы: 6

Nucleo STM32F302R8

Бренд: ST Страницы: 18

Бренд: RAK Страницы: 17

EmbCore ROM-7421

Бренд: Advantech Страницы: 25

Бренд: Ublox Страницы: 21

WizFi360-EVB-Pico

Бренд: Wiznet Страницы: 29

Бренд: BiPOM Electronics Страницы: 12

Бренд: Gigabyte Страницы: 40

GA-Z97X-Gaming G1

Бренд: Gigabyte Страницы: 136

Бренд: Thinklabs Страницы: 129

Бренд: EVGA Страницы: 40

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды