manualshive.com logo in svg

Daikin VRV EMERION RXYQ-AATJA, Руководство по обслуживанию, Страница: 157 / 429

Поделиться
Скачать
Daikin VRV EMERION RXYQ-AATJA Скачать руководство пользователя страница 157

SiUS342303E

Field Settings for Indoor Unit

Part 5 Field Settings and Test Operation

150

NOTE

<Settin

g

 confirmation screen>

(6)
(7)

Press 

Menu/OK

 button.

Setting confirmation

6. 

Press 

Menu/OK

 button. Setting 

confirmation screen is displayed.

7.

 

Select 

Yes

 and press 

Menu/OK

 

button. Setting details are 
determined and field settings 
screen returns.

8

. 

In the case of multiple setting 

changes, repea

t 

(3)

 to 

(7)

.

9. 

After all setting changes are 

completed, press 

Cancel

 

button t

w

ice.

10. 

Backlight goes out, and 

Checkin

g

 the connection

.

Please standby.

 is displayed for 

initialization. After the 
initialization, the basic screen 
returns.

• 

Installation of optional accessories on the indoor unit may require changes to field settings.
See the manual of the optional accessory.

•

 For field setting details related to the indoor unit, see installation manual shipped 

w

ith the indoor unit.

Содержание VRV EMERION RXYQ-AATJA














































































































































































































































































































































































































































Отзывы:

Нет отзывов