Chevrolet Sonic 2012 Скачать руководство пользователя страница 716

Страница: 716 / 812

Note: Install the front lower control arm rear bolt and nut hand tight to hold the lower control arm in place while tightening

the front lower control arm bolt.

2. Install the NEW front lower control arm front bolt

(1)

and tighten to.

• First Pass: 115

N·m (85

ft)

• Final Pass: plus an additional

degrees

3. Tighten the NEW front lower control arm rear nut

(1)

to:

• First Pass: 160

N·m (118

ft)

• Final Pass: plus an additional

degrees

Front Suspension

SUSPENSION

BACK TO CHAPTER INDEX

TO MODEL INDEX

CHEVROLET SONIC 2012 BODY REPAIR MANUAL

Содержание Sonic 2012











































































































































































































































































































































































































































































































































































































































































































































































































































Результаты поиска

Содержание Sonic 2012

Отзывы:

Похожие инструкции для Sonic 2012

Бренды по названию

Популярные бренды

Chevrolet Sonic 2012, Руководство по ремонту кузова

Результаты поиска

Содержание Sonic 2012

Отзывы:

Похожие инструкции для Sonic 2012

Бренды по названию

Популярные бренды