Chevrolet Sonic 2012 Скачать руководство пользователя страница 660

Страница: 660 / 812

2. Align the steering wheel module fasteners to the steering column fastener holes.
3. Push the steering wheel module

(1) firmly into the steering column in order to engage the fasteners.

4. Enable the SIR system. Refer to

SIR Disabling and Enabling

5. After replacing the module, fully deploy the module before disposal. If the module was replaced under warranty, fully deploy

and dispose of the module after the required retention period. Refer to

Inflatable Restraint Module Handling and Scrapping

Restraints

RESTRAINTS

0-8

BACK TO CHAPTER INDEX

TO MODEL INDEX

CHEVROLET SONIC 2012 BODY REPAIR MANUAL

Содержание Sonic 2012











































































































































































































































































































































































































































































































































































































































































































































































































































Результаты поиска

Содержание Sonic 2012

Отзывы:

Похожие инструкции для Sonic 2012

Бренды по названию

Популярные бренды

Chevrolet Sonic 2012, Руководство по ремонту кузова

Результаты поиска

Содержание Sonic 2012

Отзывы:

Похожие инструкции для Sonic 2012

Бренды по названию

Популярные бренды