Chevrolet Sonic 2012 Скачать руководство пользователя страница 120 | Manualshive

Страница: 120 / 812

background image

Callout

Component Name

1

Rear Compartment Lid Name Plate

• CHEVROLET
• BOWTIE

Caution:

Refer to

Exterior Trim Emblem Removal Caution

.

Procedure

1. The part and surface should be 21°C (70°F) prior to installation. The vehicle should remain 21°C (70°F) for
one hour after assembly to allow adhesive to develop sufficient bond strength.

     2. Use a Heat Gun or equivalent to remove the old nameplate. Clean all adhesive from the rear compartment
panel and wipe the surface dry with a clean lint-free towel prior to installing the new nameplate.
     3. When removing protective liners from the adhesive tape, be careful not to touch tape with hands and do not

allow tape to come in contact with dirt or any foreign matter prior to adhesion.
4. Close the rear compartment lid prior to adhesion.

5. Using the palm of the hand, wet out the emblem to the rear compartment lid to ensure full adhesion of the
emblem is made.

Rear Compartment Lid Nameplate Replacement (Sedan)

© 2011 General Motors. All rights reserved.

0-2

Exterior Trim

BODY HARDWARE AND TRIM

BACK TO CHAPTER INDEX

TO MODEL INDEX

CHEVROLET SONIC 2012 BODY REPAIR MANUAL

«
...
118
119
120
121
122
...
»

Содержание Sonic 2012













































































































































































































































































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для Sonic 2012

Бренд: ZAPTEC Страницы: 240

Бренд: LaserTrack Страницы: 12

Бренд: Daihatsu Страницы: 41

Бренд: Daihatsu Страницы: 268

PICASSO XSARA DESIRE 1.6 - MESUREMENT

Бренд: CITROEN Страницы: 2

Бренд: Paxton Automotive Страницы: 85

Бренд: Thule Страницы: 8

1306 RAPID SYSTEM

Бренд: Thule Страницы: 8

Бренд: Buick Страницы: 428

Бренд: EUFAB Страницы: 12

5TH GEN 4RUNNER

Бренд: Victory 4x4 Страницы: 5

Бренд: Keith Страницы: 2

Бренд: Chevrolet Страницы: 412

Бренд: Needit Страницы: 2

KIT ParkingSensor 814

Бренд: Gemini Страницы: 6

Бренд: Volvo Страницы: 10

Бренд: Honda Страницы: 4

Бренд: Pet Gear Страницы: 4

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды