Chevrolet Sonic 2012 Скачать руководство пользователя страница 367 | Manualshive

Страница: 367 / 812

background image

Mild Steel

This information provides repair recommendations and general guidelines for steel classified as Mild Steel. This type of steel

normally has a tensile strength less than 270

MPa. This includes the common steel names of:

• Mild Steel
• Bake Hardenable Steel (BH)
• Solid Solution Strengthened Steel

General Motors recommends the following when repairing or replacing this type of steel during collision repair.

Recommended Repairs

• Cold repairs can be performed on this type of steel, unless the damage includes kinks. If the damage includes kinks, the

part should be replaced.

• Controlled use of heat can be used to repair damage, if the heat does not exceed 650°

C (1200°

F). The heat should be

applied a maximum of 2

times, for up to 90

seconds.

• Sectioning or partial replacement of this type of steel is recommended only at approved locations, in a specific sectioning

procedure.

•  This type of steel can be used as a sleeve, or backer plate, when recommended in a specific sectioning procedure.
•  Squeeze resistance spot welding can be used to replace factory spot welds, where applicable
•  MIG plug welding and MIG stitch welding can be used on this type of steel.
•  MIG brazing can be used on this type of steel.

© 2011 General Motors. All rights reserved.

Collision Repair

BODY REPAIR

0-3

BACK TO CHAPTER INDEX

TO MODEL INDEX

CHEVROLET SONIC 2012 BODY REPAIR MANUAL

«
...
365
366
367
368
369
...
»

Содержание Sonic 2012













































































































































































































































































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для Sonic 2012

Бренд: RaceChip Страницы: 12

Бренд: RAM Страницы: 116

Бренд: TATA Motors Страницы: 159

Бренд: WABCO Страницы: 52

Бренд: Whispbar Страницы: 17

Бренд: Yakima Страницы: 9

Бренд: Gator Страницы: 8

Бренд: benbat Страницы: 14

Бренд: SPL Страницы: 5

Бренд: Magneti Marelli Страницы: 2

Бренд: Vangear Страницы: 5

Бренд: Safe Fleet Страницы: 20

A-18 TRAILER ABS

Бренд: BENDIX Страницы: 40

Бренд: Toyota Страницы: 56

Бренд: Axxess Страницы: 16

Бренд: Car-Interface Страницы: 23

Бренд: Volvo Страницы: 18

Multi Vehicle Mount MVM-35-05

Бренд: Bracketron Страницы: 4

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды