Chevrolet Sonic 2012 Скачать руководство пользователя страница 588

Страница: 588 / 812

Callout

Component Name

Preliminary Procedures

Remove the sunroof module. Refer to

Sunroof Module Assembly Replacement

Sunroof Sunshade Stops (Qty

:2)

Sunroof Sunshade

Procedure

1. Remove the stops located at the rear of the sunroof module.
2. Remove the sunshade by sliding it rearward out the ends of the module.

3. Verify the proper operation of the sunroof sunshade before securing the headliner.

Sunroof Sunshade Replacement

Roof

ROOF

0-5

BACK TO CHAPTER INDEX

TO MODEL INDEX

CHEVROLET SONIC 2012 BODY REPAIR MANUAL

Содержание Sonic 2012











































































































































































































































































































































































































































































































































































































































































































































































































































Результаты поиска

Содержание Sonic 2012

Отзывы:

Похожие инструкции для Sonic 2012

Бренды по названию

Популярные бренды

Chevrolet Sonic 2012, Руководство по ремонту кузова

Результаты поиска

Содержание Sonic 2012

Отзывы:

Похожие инструкции для Sonic 2012

Бренды по названию

Популярные бренды