Chevrolet Sonic 2012 Скачать руководство пользователя страница 114

Страница: 114 / 812

Callout

Component Name

Preliminary Procedure

1. Open and support the rear compartment lid.
2. Remove the rear compartment lid inner panel trim. Refer to

Rear Compartment Lid Inner Panel Trim Replacement

3. Disconnect the electrical connectors.
4. Remove the four nuts securing the rear compartment lid applique to the rear compartment lid.

5. Release the center retainer from the rear compartment lid.

Rear Compartment Lid Applique Nut (Qty:

Caution:

Refer to

Fastener Caution

Tighten

N·m (44

in)

Rear Compartment Lid Retainer

Liftgate Release Switch

Procedure

Remove the liftgate release switch. Refer to

Liftgate Release Switch Replacement

Rear License Plate Lamp (Qty:

Procedure

Remove the rear license plate lamps. Refer to

Rear License Plate Lamp Replacement

Rear Compartment Lid Applique Replacement

Rear Compartment Lid Applique

0-2

Exterior Trim

BODY HARDWARE AND TRIM

BACK TO CHAPTER INDEX

TO MODEL INDEX

CHEVROLET SONIC 2012 BODY REPAIR MANUAL

Содержание Sonic 2012











































































































































































































































































































































































































































































































































































































































































































































































































































Результаты поиска

Содержание Sonic 2012

Отзывы:

Похожие инструкции для Sonic 2012

Бренды по названию

Популярные бренды

Chevrolet Sonic 2012, Руководство по ремонту кузова

Результаты поиска

Содержание Sonic 2012

Отзывы:

Похожие инструкции для Sonic 2012

Бренды по названию

Популярные бренды