Chevrolet Sonic 2012 Скачать руководство пользователя страница 221

Страница: 221 / 812

Callout

Component Name

Warning:

Refer to

SIR Warning

Preliminary Procedures

1. Mark the location of the hinge before removing the bolts with a grease pencil.
2. Remove the rear door trim panel. Refer to

Rear Side Door Trim Replacement

Rear Side Door Check Link Bolt to Body

Caution:

Refer to

Fastener Caution

Procedure

1. Remove the water deflector.

2. Disconnect the door electrical connector.
3. Support the door before removing the hinge bolts.

4. With an assistant, remove the door.
5. After the door has been removed, ensure that the dome lamp is off. If the dome lamp is on remove the fuse.

Tighten

N·m (16

ft)

Rear Side Door Hinge Bolt to Door (Qty:

Tighten

N·m (24

ft)

Rear Side Door Hinge Bolt to Door (Qty:

Tighten

N·m (24

ft)

Rear Side Door Assembly

Rear Side Door Replacement

Procedure

1. When replacing the door it is necessary to transfer all of the internal components.
2. If the door striker needs adjust. Refer to

Rear Side Door Lock Striker Adjustment

3. Rear door adjustment. Refer to

Rear Side Door Adjustment

Bolted Exterior Body Panels and Closures

BODY REPAIR

0-3

BACK TO CHAPTER INDEX

TO MODEL INDEX

CHEVROLET SONIC 2012 BODY REPAIR MANUAL

Содержание Sonic 2012











































































































































































































































































































































































































































































































































































































































































































































































































































Результаты поиска

Содержание Sonic 2012

Отзывы:

Похожие инструкции для Sonic 2012

Бренды по названию

Популярные бренды

Chevrolet Sonic 2012, Руководство по ремонту кузова

Результаты поиска

Содержание Sonic 2012

Отзывы:

Похожие инструкции для Sonic 2012

Бренды по названию

Популярные бренды