Chevrolet Sonic 2012 Скачать руководство пользователя страница 368 | Manualshive

Страница: 368 / 812

background image

Ultra High Strength Dual Phase Steel

This information provides repair recommendations and general guidelines for steel classified as Ultra High Strength Dual Phase Steel

(dual phase steel with a tensile strength greater than 800

MPa), also known as DPX.

General Motors recommends the following when repairing or replacing this type of steel during collision repair.

Note:

•  Repair of this type of steel is not recommended.
•  This type of steel should be replaced at factory joints only. Sectioning or partial replacement is not recommended.
•  The use of heat to repair damage is not recommended for this type of steel.
•  Stitch welding is not recommended for this type of steel.
•  This classification of steel cannot be used as a backing reinforcement or a sleeve for a sectioning joint, unless a specific

procedure is available.

Recommended Repairs

•  Squeeze resistance spot welding can be used to replace factory spot welds, where applicable.
•  MIG plug welding can be used to replace factory spot welds.
•  MIG brazing can be used to replace factory spot welds.

© 2011 General Motors. All rights reserved.

Collision Repair

BODY REPAIR

0-3

BACK TO CHAPTER INDEX

TO MODEL INDEX

CHEVROLET SONIC 2012 BODY REPAIR MANUAL

«
...
366
367
368
369
370
...
»

Содержание Sonic 2012













































































































































































































































































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для Sonic 2012

Бренд: Yakima Страницы: 8

Бренд: Yakima Страницы: 12

Бренд: JEHNERT SOUND DESIGN Страницы: 8

Experience Series

Бренд: Rainbow Страницы: 19

Бренд: Yakima Страницы: 12

BLACK STEEL S2560

Бренд: Fab Fours Страницы: 9

1973 Convertible

Бренд: Volkswagen Страницы: 80

Бренд: Opel Страницы: 254

51 47 0 027 792

Бренд: BMW Страницы: 7

Бренд: Ford Страницы: 728

Бренд: Westin Страницы: 5

Бренд: Lexus Страницы: 34

Бренд: Toyota Страницы: 32

Бренд: Alphasonik Страницы: 8

Бренд: AutoLoc Страницы: 6

Бренд: Axxess Страницы: 16

2008 Savana Van

Бренд: GMC Страницы: 402

Бренд: Whispbar Страницы: 14

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды