Chevrolet Sonic 2012 Скачать руководство пользователя страница 162

Страница: 162 / 812

Callout

Component Name

Preliminary Procedure

1. Remove the right and left windshield side garnish moldings. Refer to

Windshield Side Garnish Molding Replacement

2. Remove the front floor console assembly. Refer to

Front Floor Console Replacement

3. Remove the right and left instrument panel upper trim panels. Refer to

Instrument Panel Upper Trim Panel

Replacement - Right Side

and

Instrument Panel Upper Trim Panel Replacement - Left Side

4. Remove the radio assembly. Refer to

Radio Replacement

5. Remove the heater and air conditioning control assembly. Refer to

Heater and Air Conditioning Control Replacement

6. Remove the instrument panel lower trim pad cover. Refer to

Instrument Panel Lower Trim Pad Cover Replacement

7. Remove the instrument panel insulator. Refer to

Instrument Panel Insulator Replacement

8. Note location and routing of the instrument panel electrical harness assembly in order to ensure proper installation.

Instrument Panel Fastener (Qty:

Caution:

Refer to

Fastener Caution

Instrument Panel Assembly

Procedures

1. With the aid of an assistant lift the instrument panel assembly rearward and upward away from the tie bar
assembly.

2. Disconnect the electrical connectors.
3. Remove the instrument panel assembly from the vehicle.

4. When replacing the instrument panel assembly, transfer all necessary components.

Instrument Panel Assembly Replacement

Instrument Panel and Console Trim

BODY HARDWARE AND TRIM

0-2

BACK TO CHAPTER INDEX

TO MODEL INDEX

CHEVROLET SONIC 2012 BODY REPAIR MANUAL

Содержание Sonic 2012











































































































































































































































































































































































































































































































































































































































































































































































































































Результаты поиска

Содержание Sonic 2012

Отзывы:

Похожие инструкции для Sonic 2012

Бренды по названию

Популярные бренды

Chevrolet Sonic 2012, Руководство по ремонту кузова

Результаты поиска

Содержание Sonic 2012

Отзывы:

Похожие инструкции для Sonic 2012

Бренды по названию

Популярные бренды