Chevrolet Sonic 2012 Скачать руководство пользователя страница 638

Страница: 638 / 812

Callout

Component Name

Procedure

Remove the rear seat cushion. Refer to

Rear Seat Cushion Replacement

Rear Seat Back Cushion Pivot Support

Procedure

1. Remove the rear outboard shoulder belts from the shoulder belt bezel and position it out of the way.

2. Pull the rear seat back cushion latch release located on the top of the rear seat back cushion, and fold the
rear seat back cushion forward.

3. Push in on the rear seat back cushion pivot support, and release from bracket.

Rear Seat Back Cushion

Procedure

1. Pull up on the outer side of the rear seat back cushion and remove the rear seat back cushion from the
bracket and hinge.

2. Transfer components as necessary.

Rear Seat Back Cushion Replacement (AMA 40% w/Split Back)

Seats

SEATS

0-7

BACK TO CHAPTER INDEX

TO MODEL INDEX

CHEVROLET SONIC 2012 BODY REPAIR MANUAL

Содержание Sonic 2012











































































































































































































































































































































































































































































































































































































































































































































































































































Результаты поиска

Содержание Sonic 2012

Отзывы:

Похожие инструкции для Sonic 2012

Бренды по названию

Популярные бренды

Chevrolet Sonic 2012, Руководство по ремонту кузова

Результаты поиска

Содержание Sonic 2012

Отзывы:

Похожие инструкции для Sonic 2012

Бренды по названию

Популярные бренды