Chevrolet Sonic 2012 Скачать руководство пользователя страница 760

Страница: 760 / 812

Air Conditioning Compressor and Condenser Hose Replacement (Diesel)

Removal Procedure

1. Recover the refrigerant. Refer to

Refrigerant Recovery and Recharging

2. Remove front bumper fascia. Refer to

Front Bumper Fascia Replacement

3. Remove air conditioning compressor and condenser hose nut

(1).

4. Remove air conditioning compressor and condenser hose

(2) from A/C condenser.

5. Remove A/C compressor and condenser hose bolt

(1).

6. Remove A/C compressor and condenser hose

(2) from A/C compressor.

7. Remove air conditioning compressor and condenser hose nut

(1).

8. Remove air conditioning compressor and condenser hose

(2) from refrigerant hose.

9. Remove air conditioning compressor and condenser hose from the vehicle.

HEATING VENTILATION AND AIR CONDITIONING

Hvac

BACK TO CHAPTER INDEX

TO MODEL INDEX

CHEVROLET SONIC 2012 BODY REPAIR MANUAL

Содержание Sonic 2012











































































































































































































































































































































































































































































































































































































































































































































































































































Результаты поиска

Содержание Sonic 2012

Отзывы:

Похожие инструкции для Sonic 2012

Бренды по названию

Популярные бренды

Chevrolet Sonic 2012, Руководство по ремонту кузова

Результаты поиска

Содержание Sonic 2012

Отзывы:

Похожие инструкции для Sonic 2012

Бренды по названию

Популярные бренды